Comfort Automation/ Security System Forums > Software Applications > Comfigurator > Occupancy Status |
Comfort Automation/ Security System Forums > Software Applications > Comfigurator > Occupancy Status |
| Moderated by: admin | ||
| Author | Post | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
|
slychiu Administrator 
|
In Comfigurator 3.13.1, (requires Comfort Firmware 7.174 and above) a useful feature has been introduced - Occupancy Status This allows Comfigurator to display the Occupancy Status is active, ie if there has been any movement in the selected zones in the premises  In the above screenshot, the occupancy status is Inactive. If there were movement detected in selected zones, the occupancy Status would be Active This is programmed as follows; Select the zones which will detect occupancy. These are normally Motion detectors (PIRS) Create a Response called eg Occupancy  In the Zone On and Off Response, assign to the Response which was created (Occupancy in this example)  In Alarms Misc Settings> Occupancy Time, enter the time to detect occupancy eg 30 minutes. This means that the occupancy will be inactive if the zone does not detect movement for 30 mnutes Assign the same Response to all the zones which will take art in Occupancy Detection  for example if 4 zones are assigned to Occupancy detection, and the occupancy time is 30 minutes, the Occupancy Status will be Inactive if zone of the zones detect occupancy within that time. If any zone detects movement in that time interval, then Occupancy is Active Last edited on Monday Apr 13th, 2020 09:13 am by slychiu |
|||||||||
|
wexfordman UCM Pi Users
|
That's a really interesting feature. I was thinking about something in a similar line for night mode intruder detection. Let's say, your house has 1 occupant, and is amred to night mode. Obviously, some sensors would be set to night mode and won't normally trigger an alarm, but let's say you have 2 sensors that are set to night mode, and both are activated within a short time frame ( one that would not be feasible for a single person to trigger). I know the logic could be programmed in to comfort, but it would be a great feature to build in automatically. For example the ability to group sensors into a trigger zone (a corridorr and bedroom sensor for example ) where you would/ could expect to trigger both zones at the same time or within a very short timferent set of sensors would be anotigger zone (say kitchen and living room). If both these trigger zones were activated at the same time, or within a set time period, then there is more than 1 person in the house....set off the alarm. It's an interesting feature for example for lone elderly people, even to the point that it could just trigger a silent alarm. It could be expanded to low for houses with more than 1 occupant also. Last edited on Wednesday Apr 15th, 2020 07:41 pm by wexfordman |
|||||||||
|
slychiu Administrator
|
This seems to be for a very specific requirement, so using Responses seems to be the best way and allows you to handle many different conditions I suggest in night node, a zone can trigger response for zone name announcement if the bedroom (or other) zone is active |
|||||||||
|
palmlodge Member
|
Many years ago, I setup occupancy for rooms, floors and whole house with timers which is in use today to turn off lights and appliances. I'll see if I can retire all that logic, thanks Last edited on Thursday Jun 18th, 2020 10:34 pm by palmlodge |
|||||||||
|
slychiu Administrator
|
This is an example of an application of the occupancy feature in an unattended warehouse where staff come in only sometimes, and the management would like to know when they do without having the staff to arm and disarm the system. The PIRE should be set to Zone Type Switch Normally Open so that it does not cause an intruder alarm. The Zone Response and Zone Off Responses are assigned to the Response named Occupancy: If Occupancy = 0 Then Send SMS PhoneNo01 1 End If Assign Occupancy Zone END How it works: If the PIR detects movement - if occupancy = 0 ie previously it was unoccupied, a custnmised SMS message #1 will be sent to Phone No 1. This SMS can be programmed eg "Warehouse Occupied". If the PIR subsequently detects movement before the occupancy Time out, it will not send more SMS. The occupancy time out can be set to 30 minutes for example depending on how long the staff are expected to remain in the facility Last edited on Tuesday Sep 19th, 2023 04:36 am by slychiu |
|||||||||
|
slychiu Administrator
|
It may also be useful for those who rent out their property, or small hotel operators. It tells them when the guests have arrived, and if they have left |
|||||||||