Comfort Home Automation/ Security System Forums Home

 Moderated by: slychiu Topic closed
AuthorPost
slychiu
Administrator


Joined: Saturday Apr 29th, 2006
Location: Singapore
Posts: 5242
Status: 
Offline

  back to top

IRIO Firmware 7.008
Bugs Fixed
  1. Fixed Dimmer to report counter.
  2. Fixed bug -Blinds AC function's down relay fails to switch off.  This is if feedback counter is assigned and it affects submodule 2 only.
  3. Fixed wrong input number reported, when Register Type is set to “Input” for “Digital Input”
New Features
  1. For Blinds AC function, extend “ignore current sensing” duration from 250ms to 1000ms. This is to compensate for hardware slow detection of low current motors.
  2. For Blinds AC function, LED is added to indicate current detection status.  The LED is turned on if current is detected.
  3. Support new “Calibration offset” parameter of Temperature Sensor input function.
  4. Input function Support of new “Virtual Input” register type, for various input functions.
  5. Supports new ISM08  submodule functions.

New Features require Comfigurator 3.11.14 and above

Last edited on Saturday Nov 4th, 2017 10:52 am by slychiu

slychiu
Administrator


Joined: Saturday Apr 29th, 2006
Location: Singapore
Posts: 5242
Status: 
Offline

  back to top

IRIO 7.009
  1. Improved IR Signal input function.  Invalid counter values (ie. >63) are mapped to value 1 instead of ignoring it.  Useful in situations where signal 1 is ON signal.

slychiu
Administrator


Joined: Saturday Apr 29th, 2006
Location: Singapore
Posts: 5242
Status: 
Offline

  back to top

IRIO Firmware 7.010

Supported new “Virtual Input” register type, for “Digital Input” input function.

Note that Comfigurator version  3.12.7 minimum is required

Last edited on Sunday Oct 7th, 2018 06:00 am by slychiu

slychiu
Administrator


Joined: Saturday Apr 29th, 2006
Location: Singapore
Posts: 5242
Status: 
Offline

  back to top

IRIO Firmware 7.014
  • Dimmer 0-10V Function, supports new “Direction” and “Quick Press” parameters. This allows different ways for the switch to control the dimmer output eg alternate pressto change direction, or only 1 direction up or down, for quick press and long press
  • Analog Output 0-10v function supports register flag assignment.
  • Analog Input (0-10v) function supports sensor value reporting, as long as sensor number is assigned (even if a Flag or Virtual Inputs is not assigned)

slychiu
Administrator


Joined: Saturday Apr 29th, 2006
Location: Singapore
Posts: 5242
Status: 
Offline

  back to top

IRIO 7.017
 Proportional + Integral ( PI)  control function in analog outputs. 
  •  Output move direction is based on Summer/Winter flag status.
  •  When PI flag is off, analog output can be controlled via counter.
  •  Supported ramping for PI output.
  •  Bumpless transfer, with CO-bias feature,
  •  When PI flag goes off, output remains unchanged.
  •  Improved register reporting.
 Take note that if PI function is used, IR transmission function will be disabled,

IRIO 7.018
Changes for  PI control function:
  • Fixed calculation error on the integral part where it is not smooth.
  • Previously in some cases, the change was every 10 seconds.
  • Changed integral sum from automatic start, instead of taking the latest set samples.
  • Double gain limit to 32.
  • Added new “Sample time” parameter.
  • Added new “Direction” parameter.
  • Set checks for integral sum overflows.
IRIO 7.019
  • Supports 4 dimmers (analog outputs) for IRIO02.
  • Support ID detection for new ISM09,
  • Note that  ISM09 (for PT100)will be identified wrongly for older firmware

Last edited on Sunday May 8th, 2022 06:19 am by slychiu


UltraBB 1.172 Copyright © 2007-2014 Data 1 Systems