| Posted: Sunday Aug 27th, 2017 09:21 am |
|
1st Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5235 |
| Status: |
Offline
|
back to top
|
IRIO Firmware 7.008
Bugs Fixed- Fixed Dimmer to report counter.
- Fixed bug -Blinds AC function's down relay fails to switch off. This is if feedback counter is assigned and it affects submodule 2 only.
- Fixed wrong input number reported, when Register Type is set to “Input” for “Digital Input”
New Features- For Blinds AC function, extend “ignore current sensing” duration from 250ms to 1000ms. This is to compensate for hardware slow detection of low current motors.
- For Blinds AC function, LED is added to indicate current detection status. The LED is turned on if current is detected.
- Support new “Calibration offset” parameter of Temperature Sensor input function.
- Input function Support of new “Virtual Input” register type, for various input functions.
- Supports new ISM08 submodule functions.
New Features require Comfigurator 3.11.14 and above
Last edited on Saturday Nov 4th, 2017 10:52 am by slychiu
|
| Posted: Saturday Nov 4th, 2017 10:40 am |
|
2nd Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5235 |
| Status: |
Offline
|
back to top
|
IRIO 7.009
- Improved IR Signal input function. Invalid counter values (ie. >63) are mapped to value 1 instead of ignoring it. Useful in situations where signal 1 is ON signal.
|
| Posted: Sunday Oct 7th, 2018 05:58 am |
|
3rd Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5235 |
| Status: |
Offline
|
back to top
|
IRIO Firmware 7.010
Supported new “Virtual Input” register type, for “Digital Input” input function.
Note that Comfigurator version 3.12.7 minimum is required
Last edited on Sunday Oct 7th, 2018 06:00 am by slychiu
|
| Posted: Wednesday Dec 11th, 2019 11:24 am |
|
4th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5235 |
| Status: |
Offline
|
back to top
|
IRIO Firmware 7.014
- Dimmer 0-10V Function, supports new “Direction” and “Quick Press” parameters. This allows different ways for the switch to control the dimmer output eg alternate pressto change direction, or only 1 direction up or down, for quick press and long press
- Analog Output 0-10v function supports register flag assignment.
- Analog Input (0-10v) function supports sensor value reporting, as long as sensor number is assigned (even if a Flag or Virtual Inputs is not assigned)
|
| Posted: Sunday May 8th, 2022 06:17 am |
|
5th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5235 |
| Status: |
Offline
|
back to top
|
IRIO 7.017
Proportional + Integral ( PI) control function in analog outputs. - Output move direction is based on Summer/Winter flag status.
- When PI flag is off, analog output can be controlled via counter.
- Supported ramping for PI output.
- Bumpless transfer, with CO-bias feature,
- When PI flag goes off, output remains unchanged.
- Improved register reporting.
Take note that if PI function is used, IR transmission function will be disabled,
IRIO 7.018
Changes for PI control function: - Fixed calculation error on the integral part where it is not smooth.
- Previously in some cases, the change was every 10 seconds.
- Changed integral sum from automatic start, instead of taking the latest set samples.
- Double gain limit to 32.
- Added new “Sample time” parameter.
- Added new “Direction” parameter.
- Set checks for integral sum overflows.
IRIO 7.019
- Supports 4 dimmers (analog outputs) for IRIO02.
- Support ID detection for new ISM09,
- Note that ISM09 (for PT100)will be identified wrongly for older firmware
Last edited on Sunday May 8th, 2022 06:19 am by slychiu
|
|
