When will the CBUS 2 board with the latest SIM be available for Purchase? Laser systems in the UK are still showing the very old ...   Wednesday Apr 16th, 2014 07:58 pm

After much searching I found an article that has enabled me to get all of the modules happily coexisting - however I am still struggling ...   Wednesday Dec 18th, 2013 07:49 pm

Hi all, I would welcome some help here if you can with the following setup. Comfort Gen2 (7.046 UCM Ethernet UCM Cbus KP06 KP04 DSM02 x2 The two DSM02's are a new addition ...   Wednesday Dec 18th, 2013 03:45 pm

Hi, Not wanting to hijack the other thread along these lines I am starting afresh. I can see the 2 Chirps the alarm produces on arming getting ...   Wednesday Dec 11th, 2013 11:00 pm

thanks for the comprehensive reply - just need to wait until the new year for the gate to be made before i can play with ...   Thursday Dec 5th, 2013 08:58 am

Hi all, Looking to add two of the Farfisa Profilo door (PL11P) stations to comfort. I assume I only need on RGR05 in the system but what ...   Wednesday Dec 4th, 2013 09:31 pm

Hi all, Gen 2 comfort running 7.045, UCM/ETH03 running 7.028, UCM CBUS running old firmware as non upgradeable board, KP06 running 6.007. I have added a KP04 ...   Wednesday Dec 4th, 2013 01:48 pm

Hi ident, Thanks for your reply - it would be really good to know if the user codes can be used in this way - did ...   Wednesday Dec 4th, 2013 01:38 pm

Hi all, I have a vintage UCM CBUS from about 2005 (Cbus 5.66 label on U1 and CBUS Sim is 1223/4). A few questions have sprung to ...   Tuesday Dec 3rd, 2013 04:51 pm

Hi Chiu, Thanks for that, will the presence of the multi link cause issues with the comfort UCM? I already have the multi link to allow ...   Sunday Dec 1st, 2013 09:59 am

Hi Chiu, Can you confirm that the UCM Heatmiser supports Multilink? I have three wifi Heatmiser thermostats around the place and it would be great if i ...   Saturday Nov 30th, 2013 03:46 pm

Hi ident, If it was possible to have the system setup to have a user code able to put the alarm into a certain state then ...   Saturday Nov 30th, 2013 09:07 am

Hi ident, Can you advise if the new smart switch mentioned just over a year ago will still see the light of day and roughly when? I ...   Saturday Nov 30th, 2013 01:14 am

Hi all, Revisiting this topic as alarm in the summer house has stopped working and rather than continuing to maintain a second alarm system and instead ...   Friday Nov 29th, 2013 11:31 pm

Hi Niall, Thanks for the reply, I had been looking at that part but was put off when it said E22 on the website - are ...   Tuesday Jul 2nd, 2013 04:09 pm

Hi all, I am looking to mount a kp06 and an SCS in the same frame - is this possible? I seem to remember seeing a ...   Saturday Jun 29th, 2013 11:48 pm

Hi all, I have had to change the bell box on my comfort 1 alarm and have tried fitting the above bell box and with somewhat ...   Friday Sep 21st, 2012 09:01 pm

Hi ident, Many thanks for the update on the firmware, I was assuming this wouldn't happen for a while so was looking for work arounds. Any idea ...   Thursday May 24th, 2012 09:10 pm

tech07 wrote: The front door should be an Entry Zone Type and the PIR should have "Entry Path" checked in the zone settings Hi Tech 07, The ...   Monday May 21st, 2012 02:44 pm

thanks ident - the relays were going to be my next question I am planning to use the relays at each end to completely isolate the ...   Saturday May 19th, 2012 09:19 pm

Hi all, Finally have the time to revisit this, so thank you to everyone for their previous replies - I am flattered you think my house ...   Friday May 18th, 2012 06:00 pm

Thanks Chiu, I think I have come up with a potential solution to the problem in that a cbus network bridge can be programmed to filter ...   Friday May 18th, 2012 02:22 pm

Hi all, As you will see from my other posts I have two Comfort panels a Gen 1 and a Gen2. I have a UCM01 RS232 (with ...   Thursday May 17th, 2012 10:22 pm

Hi all, I am after some advice on whether the following scenario is achievable. I have a CBUS network covering the House/ Garden and Outbuildings. The house ...   Thursday May 17th, 2012 08:46 pm

Hi, Have been programming my Comfort I system for a simple alarm using the latest version of comfigurator and every time I transfer the cclx to ...   Thursday Mar 1st, 2012 05:26 pm

Hi ident, thanks for your response, can you elaborate as to why I shouldn't give the cleaner a code? I thought the whole idea with Comfort ...   Thursday Mar 1st, 2012 05:22 pm

I am reposting this in Questions on using comfort as this may be more relevant Hi all, I have had a Comfort II alarm sat in it's ...   Tuesday Feb 28th, 2012 10:48 am

Hi all, I have had a Comfort II alarm sat in it's box for the last couple of years awaiting renovation of the house and subsequent recomissioning. We are ...   Monday Feb 27th, 2012 05:13 pm