KNX (EIB) > Comm failure when configuring 3rd party device on KNX BUS (7 replies - 12950 views)
This is excatly what I did to try to remove "RS485 Comm Failure" (I've used "Not Assigned"). But still, the message is displayed on the ... Monday Apr 29th, 2019 01:49 pm KNX (EIB) > Comm failure when configuring 3rd party device on KNX BUS (7 replies - 12950 views)
Hello,
I've just updated the knx UCM firmware from knx to knx2 last version.Since, I encounter very often "RS485 Comm Failure" Alert. Previously, I never had ... Monday Apr 29th, 2019 11:03 am UCM/ETH01 & UCM/ETH02 > Connecting a PC to UCM/Eth2 (21 replies - 36241 views)
Thanks.
I've already tried with the previous network config but it didn't change anything to the results.
... Monday Apr 10th, 2017 01:14 pm UCM/ETH01 & UCM/ETH02 > Connecting a PC to UCM/Eth2 (21 replies - 36241 views)
Hello,
I'm currently experiencing the same connection issue with my ETH02 module.
I can get the module worked in the following states (neither with DS explorer neither ... Monday Apr 10th, 2017 11:27 am Questions on Installation and Connection > Siren/Bellbox Connections to Comfort (27 replies - 45749 views)
At 12VDC the siren is switched on
Above 13VDC the siren switches off.
... Wednesday Aug 29th, 2012 02:15 pm Questions on Installation and Connection > Siren/Bellbox Connections to Comfort (27 replies - 45749 views)
I've changed this configuration but the voltage is not high enough (checked 12VDC with voltmeter) and the siren doesn't remain disable. ... Wednesday Aug 29th, 2012 07:44 am Questions on Installation and Connection > Siren/Bellbox Connections to Comfort (27 replies - 45749 views)
Hello,
I've a similar issue.
I've got a siren box that only need to be triggered to be enabled. The siren manages its own melody and includes ... Tuesday Aug 28th, 2012 03:43 pm KNX Support > UCM / KNX group adress limitations (6 replies - 12713 views)
Hello,
I redo the same than yesterday and now it works ??? Fine.
But I did the mapping of the the group adresses to Physical inputs (used ... Wednesday Aug 22nd, 2012 10:20 am KNX Support > UCM / KNX group adress limitations (6 replies - 12713 views)
I did several read and write but nothing change...
Moreover, the upload with the initial group adresses at the end of the test works fine
... Tuesday Aug 21st, 2012 01:18 pm KNX Support > UCM / KNX group adress limitations (6 replies - 12713 views)
Hello,
I'm wondering if there are some limitations with the group adress that we can use on the UCM/KNX inteface. Can we use any group adress ... Tuesday Aug 21st, 2012 10:11 am Questions on Using Comfort > pseudo-random genreator (1 reply - 4504 views)
Hello,
Is yhere a way either to program a pseudo-random generator in Comfort either to use the one that's already implemented for vacation programs ?
The purpose ... Wednesday Jun 6th, 2012 09:22 pm Keypad > KP04 Power supply issue (3 replies - 7309 views)
Hello,
I let it off for a while and it changed nothing.
By the way, it was not the capacitor that was hot but it is the ... Friday Jun 1st, 2012 09:46 pm Keypad > KP04 Power supply issue (3 replies - 7309 views)
Hello,
I disconnected the KP04 from main power to move it to another place. Before it was working fine. But when I reconnected, there were no ... Monday May 28th, 2012 12:16 pm KNX Support > UCM/KNX Virtual Input Question (12 replies - 21438 views)
----------- ----------- <-- IN 0/0/70 <-|
| Comfort | <=> | ... Tuesday Feb 21st, 2012 04:09 pm KNX Support > UCM/KNX Virtual Input Question (12 replies - 21438 views)
Thanks for the support.
I understood your point and I tested it. It works fine.
So now everythink is fine and I will use this solution.
The purpose ... Tuesday Feb 21st, 2012 07:19 am KNX Support > UCM/KNX Virtual Input Question (12 replies - 21438 views)
Thanks for the support.
I understood your point and I tested it. It works fine.
So now everythink is fine and I will use this solution.
The purpose ... Tuesday Feb 21st, 2012 07:19 am KNX Support > UCM/KNX Virtual Input Question (12 replies - 21438 views)
You're right. I would still be able to control the light if Comfort is down.
Regarding the sentence you didn' understand. Let me explain you in ... Monday Feb 20th, 2012 01:16 pm KNX Support > UCM/KNX Virtual Input Question (12 replies - 21438 views)
Thank you for your answer. I will apply it if there is no another option.
The point is that I want to avoid as much as ... Monday Feb 20th, 2012 12:09 pm KNX Support > UCM/KNX Virtual Input Question (12 replies - 21438 views)
I agree with you. Normally, the sensor should send the OFF set. But I've set-up it in order not to do that because those same ... Monday Feb 20th, 2012 08:18 am KNX Support > UCM/KNX Virtual Input Question (12 replies - 21438 views)
Hello,
Using Comfort Opt with an UCM/KNX, I've mapped a virtual port to a KNX sensor. So, when the sensor detects a failure it returns a ... Sunday Feb 19th, 2012 08:19 pm |