....You can see the Comfort system (on the left wall) that makes up part of Simon's HA setup which is at the centre of this ...   Thursday Dec 29th, 2016 01:11 pm

Thanks for that, will give it a whirl... Vangelis ...   Monday Sep 5th, 2016 03:06 pm

I have not played with my Comfort config for sometime now (as its stable), however I know on my PC where I store all my ...   Monday Sep 5th, 2016 02:26 pm

There are two ways to check... 1) Check to see what Comfort is doing with the digital output (can do this real-time through Comfigurator) 2) Check the ...   Monday May 23rd, 2016 07:19 pm

Yes it is... You arm Comfort and it closes a digital output that Fibaro dry-contacts are connected to. This triggers the Fibaro Binary Sensor to send a ...   Friday May 20th, 2016 03:31 pm

If you've pulled the KP06 out of its housing it maybe worth running a short bit of Cat6 between the panel and the KP06. This ...   Sunday Apr 24th, 2016 04:21 pm

Sorry for any confusion :) This is why I don't use my ZWave/UCM....(never could get it to do what i wanted) Vangelis ...   Wednesday Jan 27th, 2016 07:18 pm

My understanding is that there can only be one ZWave Master. This will normally be Comfort (in order to gain status of ZWave nodes) In your ...   Tuesday Jan 26th, 2016 09:52 pm

The pivotal thing here (and something that will undoubtedly be missed) is the differentiation between Cloud and Standalone automation. So much of the systems now ...   Sunday Jan 10th, 2016 02:58 pm

As we are going through the elimination process to try and get to the bottom of these issues - Try pulling the mains feed for ...   Saturday Jan 9th, 2016 04:05 pm

Who installed your system? Have you done any fault finding? If you have frequent failures on the keypad and you don't mind some wiring, I would remove ...   Sunday Dec 27th, 2015 01:22 am

Does your dvr have a serial output? Might be able to use this to chat to Comfort if you have the right UCM Alternatively (and dependant ...   Wednesday Dec 23rd, 2015 01:13 pm

You can use Comfigurator Software to change Sign-In if you have a UCM/Eth connection. Vangelis ...   Monday Oct 19th, 2015 06:35 pm

Ok, good, so that rules out any latency in Wireless comms... Next, (if you have a UCM/Eth) I would take a look at the realtime Serial ...   Monday Oct 19th, 2015 10:16 am

Are all these sensors wired or wireless? Vangelis ...   Thursday Oct 15th, 2015 11:37 am

The problem is, what Dubourg is suggestion is technically quite difficult to achieve, as in effect you are proxying the call with user interaction...The suggestion ...   Monday Oct 5th, 2015 10:22 am

There maybe a subtle setting on the DECT handset that caused your issue. Glad it's sorted Vangelis ...   Sunday Oct 4th, 2015 03:13 pm

Are your internal phones DECT or wired? If DECT then try a wired one if you have it. Sounds like there maybe a cable / ...   Sunday Oct 4th, 2015 01:41 pm

Hey All, Can someone at Cytech let me know the best serial string to use to check against when Comfort is alarming (intruder). I don't want ...   Saturday Sep 5th, 2015 11:10 pm

Thanks Slychiu I never got the UCM/Zwave working as it should, however I like your sneaky way of using a Pulsed Output ;) Vangelis ...   Thursday Aug 27th, 2015 05:11 pm

Hi all, I tried (and failed) with the UCM/ZWave module - mainly as I misunderstood the concept of it's workings... So I now have UCM/Eth2 interaction via ...   Thursday Aug 27th, 2015 03:28 pm

@slychiu - You don't need to as the dimmer module learns codes from remote. In effect, you can pick any ones from Comforts library and ...   Thursday Aug 20th, 2015 04:48 pm

Sure... Comfort has some pre-stored (vendor) IR codes and can 'blast' them out via an IR Tx (http://www.cytech.biz/infrared_led_module.html) that is connected to the Comfort Panel. Using ...   Thursday Aug 20th, 2015 01:20 pm

Cool....Do you have a link to the iButton module you are using?? I am guessing this takes care of the enrolment etc of new 'buttons'? Vangelis ...   Thursday Aug 20th, 2015 01:09 pm

As an alternate method of control - Have you thought of using Comforts IR capabilities? You would have to use and IR Rx module as your ...   Monday Aug 17th, 2015 10:42 am

My situation is residential. If they took my keys, they would also have my car! Just as if they were on the worktop. All my ...   Wednesday Jul 22nd, 2015 12:34 pm

The thought process behind this was as follows ...... Elderly relatives can use iButton as opposed to trying to enter code on small keypad (KP06 in ...   Tuesday Jul 21st, 2015 06:30 pm

Had a quick search regarding iButtons on this forum and it indicates they might be supported, however I am struggling to find out which UCM ...   Sunday Jul 19th, 2015 08:34 pm

Comfort can interface with various Home Automation technologies such as ZWave, KNX and CBus. It can then control these via it's own logic engine. For ...   Monday Jul 13th, 2015 02:16 pm

I have run Comfort systems since 2002 and found them very flexible and forgiving (by this I mean resettable fuses if you do something stupid) As ...   Monday Jul 13th, 2015 12:52 pm

If your property doesn't have a Broadband connection, then there are plenty of GSM based standalone systems out there (I would go for a PIR ...   Thursday Apr 23rd, 2015 01:50 pm

I am currently working on my Comfort Ultra II systems and based just outside Southampton and happy to run through some stuff with you. What area's ...   Thursday Apr 9th, 2015 06:45 pm

Thanks Ingo - I can then check for the Disconnect and fire an alert Vangelis ...   Monday Mar 9th, 2015 05:23 pm

Hey HB - Weirdly I went through the same thing you did before I got it solved. I would telnet to Comfort on my Win7 machine ...   Monday Mar 9th, 2015 03:24 pm

btw does the iPhone app send the text to Comfort in this way?? ie Hex 03 and Dec LI1234 Vangelis ...   Thursday Feb 19th, 2015 03:53 pm

Ahh - Got you now. I will try this out again when in front of my system. Thanks.. Vangelis ...   Thursday Feb 19th, 2015 03:48 pm

Thanks Slychiu So what's the difference between pressing the HotKey to send /03 followed by me typing LI1234 and just typing /03LI1234 (without pressing the Hotkey) ...   Thursday Feb 19th, 2015 03:01 pm

Hmm strange - So are you now saying that to login with Clear Terminal you use /031234 (without the LI as opposed to /03LI1234) What Win ...   Thursday Feb 19th, 2015 01:21 pm

Update... Using my Win XP machine I can carry out the following with success... telnet to Comfort IP (port 1001) and issue Control+C followed by LI1234 I see ...   Wednesday Feb 18th, 2015 08:20 pm

Thanks Slychiu - Will have another try when I am infront of my system. Vangelis ...   Tuesday Feb 17th, 2015 05:44 pm