That simply was not my experience. I was home, the doors were open, Security was OFF. And I had the full siren bell going while I ...   Wednesday Sep 20th, 2023 07:49 am

Thanks for that information, slychiu. I can see how it’s all linked together now. I just checked my configuration and some of the Zone Types have ...   Tuesday Sep 19th, 2023 02:28 pm

I’ve recently had a situation where a particular zone went into trouble mode. So I disabled it via Comfigurator. My Comfort installer took a look yesterday ...   Thursday Sep 7th, 2023 08:17 am

Thanks, slychiu, I understand. I've lightly tweaked my response programming to be better at clearing flags anyway. Handy to know about though. ...   Saturday Oct 20th, 2018 02:00 pm

Yesterday I installed Comfigurator v3.12.8 and used that to update my Comfort firmware to v7.142. I immediately noticed that my Comfort controlled external lights were ...   Saturday Oct 20th, 2018 12:48 pm

slychiu wrote: The security mode is set at the point of starting to arm so that this can be tested Excellent, that sounds like just the ...   Sunday Jan 10th, 2016 06:49 pm

Hey folks, I'm just tinkering with how my external lights are controlled by Comfort. When I arm Comfort into Away or Vacation mode I have a Zones/Inputs ...   Saturday Jan 9th, 2016 03:58 pm

Sorry, no idea. Haven't needed to look for it TBH! ...   Monday Jan 20th, 2014 10:31 pm

I tried a couple of light sensors which were terrible, for one reason or another, but the one I'm using now which has been faultless ...   Monday Jan 20th, 2014 10:30 pm

Wimphot wrote: 2/. I cannot program with a Mac (although I think this may have changed - I have a UCM/Eth which I bought some ...   Monday Jan 20th, 2014 10:24 pm

Updated my profile to show a better location. I'm near High Wycombe/Aylesbury/Oxford. Stuart (B), hence Stub. ...   Sunday Nov 3rd, 2013 12:17 pm

Devastated to hear you have the same temperamental problems with your Zwave as I'm having with the Ulti. I clearly have some learning to do ...   Sunday Nov 3rd, 2013 09:52 am

Thanks for that, Julian. I'm very, very interested in how you get on so I can understand how to hook-up Heatmiser with Comfort. Sounds like ...   Sunday Nov 3rd, 2013 09:45 am

Not strictly Comfort related but here goes anyway. At the moment I'm using a UCM/Ulti with a few Ulti switches. These work well enough though among ...   Saturday Nov 2nd, 2013 08:04 pm

While browsing about the UCM/Zwave to augment or replace my current UCM/Ulti I came across this. I didn't know about the UCM/Heatmiser but am very ...   Saturday Nov 2nd, 2013 07:40 pm

Is there any updated UCM/Ulti firmware that I should apply? I can't see any listed explicitly here and I'm unclear if I should be using the ...   Friday Oct 19th, 2012 05:21 pm

I too get my Comfort related stuff from Laser at the URL AdrianL listed above. ...   Thursday Apr 19th, 2012 05:00 pm

Couldn't be sure, Julian, I got it with my original Comfort install several years ago. You're right, it just fits one UCM and I have ...   Monday Mar 19th, 2012 06:31 pm

The EN01 doesn't have any mounting points like we're pointing at in the second picture above. Just holes so something could be screwed in from ...   Sunday Mar 18th, 2012 10:20 am

That's fair enough! I'll look into Vacation Mode instead then. Thanks, ident. ...   Sunday Mar 18th, 2012 10:14 am

I've recently had a second UCM added to my Comfort system and needed a new enclosure to hold it all as it didn't quite fit ...   Saturday Mar 17th, 2012 07:05 pm

Any suggestions on how I might randomise a time program without being in Vacation mode? The Vacation Programs section in Comfigurator suggests that the Hours ...   Saturday Mar 17th, 2012 03:24 pm

Is the UCM/Zwave3 available to buy in the UK yet? ...   Tuesday Mar 6th, 2012 04:10 pm

"Rear" I currently have to use "Reverse" instead. ...   Monday Feb 13th, 2012 05:39 pm

Thanks, Chui. I grabbed a copy to examine. ...   Monday Jan 16th, 2012 05:11 pm

The ULTIman.pdf file (UCM/ULTI Comfort to Ulti Interface) states that, A sample program ULTIdemo.cclx for Comfigurator is supplied, which ...   Sunday Jan 15th, 2012 08:25 pm

My installer and I upgraded my Comfort Ultra ][ firmware to 6.011 the other day. We also updated my Ethernet UCM firmware and Comfigurator to ...   Sunday Jan 15th, 2012 10:19 am