Hi, Many thanks for your help previously with my RS485 issue. Issue is now resolved per your advice and Gary Morgan. System working well. I am ...   Thursday Aug 30th, 2018 09:24 am

Hi, I did a reset. The red light blinked, then the green light blinked. Red light then blinks and then green light and so on. This is ...   Friday Jun 29th, 2018 09:46 am

Hi, My CLX file was bigger than 700000 bytes so I am not able to attach. ...   Thursday Jun 28th, 2018 02:24 pm

Hi, I am not sure yet - why RS485 comms are down. There were no hardware changes or otherwise.  I have done the following - 1 Removed all ...   Thursday Jun 28th, 2018 02:21 pm

Hi, I have bought UCM Modbus RS485.  Can I add the ETH03 to convert Modbus TCP? ...   Thursday May 17th, 2018 09:12 pm

Hi. Can ISM06/ISM07 when given 240v input set flags or counters?  If so how is done? ...   Thursday May 17th, 2018 09:08 pm

Many thanks for your help.:) ...   Thursday May 17th, 2018 08:57 pm

Hi, Can ISM007 switch boilers, two port valves or pumps on directly? Do the relay provide enough to switch these on. If not how can these used? I ...   Saturday May 12th, 2018 04:53 pm

Hi, I am slightly confused when the PIR off response on a zone is initiated. Has there got be at least one ON response activated before an ...   Thursday Jan 19th, 2017 02:34 am

 Slychiu, may I ask to you consider as matter of urgency to make changes (which as a Software Engineer I think are low risk and ...   Thursday Nov 24th, 2016 03:52 pm

Comfort supports the following sensor message types. Sensor Multilevel V4,  Multilevel Sensor Nearly all ZWave devices that have sensor capability will ...   Wednesday Nov 23rd, 2016 01:42 am

Please see my new thread ZWave Hints and Tips - for Sensors Edit  by Admin Link http://www.comfortforums.com/forum62/4563.html ...   Wednesday Nov 23rd, 2016 01:39 am

Hi perhaps people can add there own insight, tips and thoughts. Here is mine First thing to understand is Zwave itself. Step 1 The controllers Primary and Secondary ...   Saturday Oct 22nd, 2016 05:38 pm

Hi, Just checking. Did you get my email with Monitor output? ...   Monday Aug 1st, 2016 08:18 pm

Hi Not sure where the issues resides but let me describe the problem first. When I have a Response coded as e.g TESTEXAMPLE response coded as Do Response1 Do ...   Thursday Jul 28th, 2016 01:43 pm

Hi, I have the wired version of Fibaro Smoke Sensor  FGSS-001 that is wired to comfort. This device supports Multilevel Sensor V1. I thought "sensor" would be available ...   Monday Apr 18th, 2016 07:59 pm

Hi, Is there a general purpose template for a response design for presence detection that I can use as basis for shutting off lights or heating? ...   Monday Mar 28th, 2016 12:32 am

Hi, Thank you for the rely. The Most useful would be 1 Run Mode Map Addr 23 As my radiators are not connected ...   Monday Mar 21st, 2016 03:11 am

Hi, I have Heatmiser and it is running well. It controls DHW, underfloor electric and thermostats. All timers are controlled by Comfort. DHW timers removed from ...   Wednesday Mar 16th, 2016 11:46 pm

For review of QUBINO dimming module see http://www.vesternet.com/blog/2015/05/awesome-qubino-z-wave-range-stock-at-vesternet/ ...   Tuesday Feb 2nd, 2016 12:40 pm

Hi, Just to make clear  ZWave plus  modules will not work with UCM ZWave if its encrypted. It will work if commands are not encrypted and the commands ...   Tuesday Feb 2nd, 2016 12:38 pm

Hi, Just to make clear  ZWave plus  modules will not work with UCM ZWave if its encrypted. It will work if commands are not encrypted and the commands ...   Tuesday Feb 2nd, 2016 12:38 pm

Hi  I just want to clarify regarding ZWave plus standard modules. ZWave UCM should work with any ZWave plus module as long as the module does not ...   Monday Feb 1st, 2016 09:28 pm

Hi  I just want to clarify regarding ZWave plus standard modules. ZWave UCM should work with any ZWave plus module as long as the module does not ...   Monday Feb 1st, 2016 09:25 pm

Hi, I have RIO connected very closely to comfort main motherboard and have UCMs and RIO connected via the 4 way headers. The RIO is the last ...   Saturday Jan 16th, 2016 05:23 pm

I have Comfort (7.077), UCM 7.065 universal  + ETH02 so that I can follow the set up instructions for LigIhtWaveRF.  I do have ETH03(which I ...   Wednesday Sep 2nd, 2015 12:18 am

Hi,  Can Honeywell 12v/24v C02 Alarm 2 wire - can they be used with comfort? Are there any issue to consider if they can be? Wiring considerations ...   Friday Apr 17th, 2015 12:20 am

Hi  I will install CAT6 shielded near to door for later installation of door station, when budget allows. In the mean time - how do I connect ...   Monday Dec 29th, 2014 04:16 pm

I have 5.183 firmware for Comfort.I have recently bought EN03 and set its ID as 1. However I cannot communicate with EN03.There was was recent ...   Friday Nov 21st, 2014 01:22 am

Hi, I have purchased Dimplex Smart fan convector radiators: these have a pilot wire when energised will set the radiator into ECO mode. The wire requires ...   Wednesday Nov 12th, 2014 12:20 am

Hi, I have a UCM ETH03 and UCM AUDIO on UCM5 - their IDs  set as  2 and 3 respectively via DIP switches and SHUNTs. I am not getting a ...   Monday Oct 13th, 2014 12:56 am

Hi, I need to get access to TEL IN, TEL OUT on main board to add the ADSL board, however LEM board with plastic stand offs ...   Monday Oct 13th, 2014 12:42 am

From the lightwave forum I am using it with Crestron. I have fixed it Wednesday (17.Sep.2014) by adding “100″ in front of every command.All you have ...   Sunday Sep 28th, 2014 05:14 pm

Hi, I am planning on using Lightwave RF,  Heatmiser UCM and ETH03(UCM06+ETH03)Can I have one Universal UCM for lightwave RF and Heatmiser simultaneously?.Or do I need ...   Friday Aug 1st, 2014 02:45 am

Hi, I like to use lightwave RF.Can I use / combine universal UCM with ETH03 and download UDP proticol as stated in the upgrade needed for ...   Friday Aug 1st, 2014 01:46 am

When buying heatmiser UCM; the documentation states RS485 or Ethernet. Does this meanEither Universal UCM + RS485 orUCM06 + ETH02 orUCM06 + ETH03 Are all three ...   Friday Aug 1st, 2014 01:21 am

This is in my planning. I am hoping to use Heatmiser, Z-wave and comfort as the backbone for my home automation plans. I am moving ...   Wednesday Sep 2nd, 2009 09:30 am

Hi, I am about to install 2 wire ACT ZDW232. I am hoping I can use one of Merten patress box insert in a wall socket. ...   Tuesday Sep 1st, 2009 03:23 pm