there is no beep when sending off code , and there is only beep when send on  code . ...   Sunday Sep 19th, 2010 07:00 am

the ir code .raw ...   Wednesday Sep 15th, 2010 08:17 am

i will send the ON code ...   Tuesday Sep 14th, 2010 12:37 pm

i am sure it is the OFF code not ON codei will send u the ir file and will check if the dome sent off ...   Tuesday Sep 14th, 2010 12:36 pm

thanx for ur support  and fast reply , i learn the ir codes but there is problem the air condition is switched on from the ...   Tuesday Sep 14th, 2010 11:00 am

the device didn't work, but there message (the signal needs 30 byte ) , what this message mean? ...   Thursday Aug 26th, 2010 08:47 am

i take this print screen from IR learner program, please check this pic ...   Thursday Aug 26th, 2010 08:27 am

i will send u the file.ifr for this problem and please check if there is a trouble  in this file ...   Wednesday Aug 25th, 2010 08:34 am

i am already measured the vlot between srn+ and srn- not between srn- and com when i disconnected the siren driver it measured the same number ...   Friday Jul 23rd, 2010 05:21 am

I am using Comfort Ult, Pc900 firmware version 5.183. I am connecting Comfort PCb, KP03, DP03 , pir and UCM05. when i make test on siren i ...   Thursday Jul 22nd, 2010 01:45 pm

When we write the UCM command like (M!011234) the driver which we are trying to built  convert it to Hexadecimle (4D 21 30 31 31 32 ...   Thursday Sep 10th, 2009 07:22 am

When i built my driver the Vantage system send the Pasword by Hexdecimal and Comfort can not understand the password in Hexdecimal . is there ...   Wednesday Sep 9th, 2009 09:25 am

Thanks it works fine ...   Thursday Sep 3rd, 2009 10:08 am

hi , I am using comfort II Ultra firmewire 164.  I have a problem i dessigned a circuit to make on and off when i connected it ...   Thursday Sep 3rd, 2009 08:50 am

hi. there adistributer in my countery for Vantage system and we want to make interface between Comfort and Vantage system . what is the requirments for ...   Monday Aug 31st, 2009 04:08 pm

Hi everyone, I am using Comfort Ult, Pc900 firme ware version 5164 . I am connecting Comfort PCb, KP03, DP03 and UCM05. When i am testing the system ...   Wednesday May 13th, 2009 01:45 pm

how can i do this command ? and send it   ...   Sunday May 10th, 2009 09:23 am

Hi every one, When i press on  any button of SCS after that the led of pressed button flashing ,   Is there any way to stop this flashing led ...   Sunday May 10th, 2009 08:59 am

this part is dimmer with 4 channel connecting with C_BUS system it is posible to connect it with comfort ...   Thursday Jan 15th, 2009 12:53 pm

Hi,      it is possible to connect dimmer (Ls504D2A) with comfort , if it is bossible how i connect it with comfort by UCM\C_BUS ? thanks   ...   Thursday Jan 15th, 2009 12:38 pm

Hi,      if i have a PABX , I will check the box in comfigurator, and i will choose the number of digit to dial for outside line ...   Monday Jan 5th, 2009 11:13 am

please confirm the IRD01 wiring terminal, J2-is connected to any RIO input (RX). J2- GND is connected to the COM of the same Rx input. J1-LED is connected ...   Thursday Dec 25th, 2008 06:12 am

thank u.   ...   Wednesday Dec 24th, 2008 09:53 am

But IRRo1 have 3rd wire GND , i read this in RIO module & IR dome . this what i read in the Module (IRR01) to ...   Wednesday Dec 24th, 2008 09:23 am

how can i connect the GND of IRR01 to The RIO PCB? THANKS ...   Wednesday Dec 24th, 2008 07:46 am

thank u ...   Monday Dec 22nd, 2008 09:27 am

Hi , Please , how i can formating the U4? ,,I think it can be formated by UCM05 . If it is possible how can i do? thanks ...   Monday Dec 22nd, 2008 07:26 am

Thanks for helping . It works well . ...   Monday Dec 22nd, 2008 06:24 am

i did not identify the UCM at module configuration and download it into system so i could not down load any modification . how to solve this? ...   Sunday Dec 21st, 2008 12:26 pm

work like a charm thanx ...   Thursday Dec 18th, 2008 12:48 pm

i did follow your instruction but it PS didn't changed  (attached screen shoot) please note that my system is ULTA II and the file that i ...   Thursday Dec 18th, 2008 11:39 am

Please, i lost the engineer code , i want a comfort configurator less than 2 . {an older Version of Comfigurator (< 2.0) and use the User ...   Thursday Dec 18th, 2008 10:37 am

Hi I did not identify keybad at Module Configuration and download it to system , So i could not later download any modification because i can not ...   Thursday Dec 18th, 2008 08:43 am

when , I am trying to download the program from pc to comfort there is awarning message this message as below. what shall i do? thanks ...   Wednesday Dec 17th, 2008 11:14 am

HI, How we choose feedback type in submenu? rgds ...   Tuesday Dec 16th, 2008 07:06 am

what the meaning of (Show Alarm) in Comfort programe?   ...   Monday Dec 15th, 2008 06:42 am

What are (Zone Auto-Shunt Count) and (Show Alarms) mean? I read the help but i can not understand them . ...   Sunday Dec 14th, 2008 10:26 am

What is the CMS specefications? ...   Sunday Dec 14th, 2008 07:50 am

In the siren(jp9) ,why we put a 1K-ohm pull up resistor? NOTE: This question in Comfort 2 Installation Manual . ...   Sunday Dec 14th, 2008 07:00 am