...   Friday Aug 31st, 2007 01:05 pm

David, thanks for the introduction. We will point to Mainlobby as another user interface into Comfort. We are keen to try it out ourselves, and ...   Wednesday Aug 29th, 2007 01:30 am

I am not sure what you mean by this If you sign in with a user code say LI1234, that is accepted with reply LU01 and ...   Monday Aug 27th, 2007 01:41 pm

Comfort is now able to comply to EN50131 and PD6662 (UK Implementation). CP9000-ULT/EN03 is the Comfort Control Panel part number using the new EN03  enclosure ...   Sunday Aug 26th, 2007 01:18 pm

The X10 telephone cable should be reversed ie pin 4 to 1, 3 to 2, 2 to 3, and 4 to 1 The picture below from ...   Saturday Aug 25th, 2007 03:06 am

We only recently identified the cause of this problem. It only occurs in the UK (on some telephone lines?) due to BT giving a Dial ...   Friday Aug 24th, 2007 01:44 pm

We should warn everyone that putting in a new voice will erase all the messages including Greeting, new, saved, Reminder Messages, Alarm Voice Messages so ...   Friday Aug 24th, 2007 12:45 pm

Kate's voice has been re-edited to improve the gaps between the words so that it sounds better, download from http://www.cytech-technology.com/temp/software/kate26.bin This will replace Anita as the ...   Thursday Aug 23rd, 2007 09:11 am

R!64 does activate Response 100, we have checked that. To make sure that Response 100 is as you expect, go to Engineer  Menu 3,6 Response ...   Wednesday Aug 22nd, 2007 12:42 pm

There may be more than 1 firewall on the machine, eg Windows Firewall? Is it possible to try it on another network? ...   Wednesday Aug 22nd, 2007 09:28 am

I am afraid I dont see the problem at all R!64 activates Response 100 Compter Room R!74 is  not valid as Response 116 does not exist, it ...   Wednesday Aug 22nd, 2007 09:20 am

    This section is for Cytech/Comfort Installers in the UK to list their details and contact info. It would be best if installers listed have ...   Sunday Aug 19th, 2007 05:23 am

The new version of Infrared Learner 1.2.1.1 is attached. The bug which caused the software to be unable to save the raw file is fixed ...   Friday Aug 17th, 2007 06:24 am

We will contact you offline on this matter for more details ...   Friday Aug 17th, 2007 06:10 am

Check out the support pages of the ethernet device manufacturer eg http://wiki.tibbo.net/doku.php/find_behind_gateway and http://wiki.tibbo.net/doku.php This may offer some clues to your situation ...   Friday Aug 17th, 2007 04:52 am

Market Overview from the Frost and Sullivan Report 30 July 2007 Retrofit Applications Hold Unlimited Potential for the European Home Automation Market Characterised by rapid expansion and ...   Thursday Aug 16th, 2007 02:29 pm

Could there be a problem with your network if it worked before? are you able to ping the UCM/Ethernet ...   Thursday Aug 16th, 2007 02:09 pm

Computer Room Lights is fixed at Response 100. When/Under what circumstances does it  become 116? ...   Thursday Aug 16th, 2007 02:01 pm

Just a Comfigurator problem, dont worry ...   Thursday Aug 16th, 2007 09:04 am

This has been traced to Comfigurator handling of long Responses, and will be fixed in the next release. Thanks for your feedback ...   Thursday Aug 16th, 2007 03:32 am

Have you left the Tamper input disconnected? This could be causing am alarm, and thiuius the red led to flash. Disconnect everythng except a keypad ...   Thursday Aug 16th, 2007 03:12 am

This can be changed by editing of each word to reduce the silence before and/or after each word. This is not the final version of ...   Thursday Aug 16th, 2007 02:30 am

Are you using a local phone to do the arming? This would be a local arming operation if you arm by remote phone, you should not ...   Wednesday Aug 15th, 2007 01:56 pm

In Configuration, Use Branch Actions is not checked. If you have Comfort II, can you try checking this box and see if the same problem ...   Monday Aug 13th, 2007 01:28 pm

We have already instructed our production to stop applying the adhesive tape, as we had other complaints about the same matter Thanks for the feedback ...   Friday Aug 3rd, 2007 09:31 am

You will have to investigate whaty exactly stopped working Is Comfort still working as normal, are you able to sign in and hear the voice etc Is ...   Friday Aug 3rd, 2007 05:46 am

A Harmony remote control is a good way to learn IR Codes into Comfort. You can download the IR codes from the Harmony website and ...   Friday Aug 3rd, 2007 05:11 am

I am pleased to announce that the new IR learner software with the ability to convert Pronto Hex codes is availlable for testing, see http://www.comfortforums.com/view_topic.php?id=745&forum_id=50 ...   Friday Aug 3rd, 2007 04:33 am

As many users have requested, our Comfort IR Learner now has the ability to convert Pronto Hex Codes into the Comfort IR format This allows ...   Friday Aug 3rd, 2007 04:31 am

correct, and you dont have to use network bridges ...   Thursday Aug 2nd, 2007 01:00 pm

adlim wrote: Y?0000 would mean all outputs 1-64 are all off. Correction to this statement Y?0000 means that 16 outputs (1 to 16 are off) The parameter consists ...   Thursday Aug 2nd, 2007 12:25 pm

After a system reset, the KP04 Home/Armed led may not turn on to indicate the security mode. However after the system is armed for the first ...   Thursday Aug 2nd, 2007 08:05 am

Comfort has 8 mailboxes which can be assigned to users each with their own sign in code. Alternately the answering machine can also be configured ...   Wednesday Jul 11th, 2007 01:46 pm