Just as I suspected, The reason for this is to do with polling of the modules by Comfort When the system is reset, it will auto-arm ...   Wednesday Jun 4th, 2008 01:32 am

Document updated June 2008 to remove the part about auto-logout at midnight which is no longer applicable http://www.cytech.biz/Downloads/Files/163/rs232.pdf ...   Tuesday Jun 3rd, 2008 01:39 pm

Zone Trouble means that you have programmed a Zone but there is a short or open circuit on the zone, when the zone is configured ...   Tuesday Jun 3rd, 2008 12:16 pm

Zones set as Door/window do not cause alarms on Comfort if the system is not armed, regardless of which version or firmware or UCM Can you ...   Tuesday Jun 3rd, 2008 05:06 am

When you reset Comfort, any open 24 Hour zones like Panic and Tamper will cause an alarm in Comfort. It is a security issue and ...   Tuesday Jun 3rd, 2008 02:37 am

You are correct, Comfort does not logout the UCM at midnight. This is Comfort not the UCM which does this and it happened quite some ...   Monday Jun 2nd, 2008 02:44 pm

The security application state is always sent to C-Bus when the change occurs, eg zone open, close, arm disarm, alarm etc At Reset, Comfort will remaiin ...   Monday Jun 2nd, 2008 02:36 pm

Yes, X10 is suitable for simple appliancfes and lights which are not critical to your needs. A few X10 modules in the house can be ...   Monday Jun 2nd, 2008 02:02 pm

Hi Kobus I dont why the zone response is able to switch the Cbus relays but you are unable to see the GAs on the CBus ...   Sunday Jun 1st, 2008 10:16 am

Your On Response and Off Response for each PIR should switch the C-Bus lights on that address. However make sure you have the C-Bus group ...   Sunday Jun 1st, 2008 08:29 am

The DT query was implemented only in a later firmware version ...   Sunday Jun 1st, 2008 02:06 am

You can upgrade by buying the IC01-UCM. This replaces the microcontroller on the UCM labelled with the firmware. You will need a PLCC IC Extractor ...   Sunday Jun 1st, 2008 01:57 am

Are the Device Server settings correct as shown on page 40 of the UCM Manual? ie the serial baud rate, parity etc. Set Flow Control to ...   Saturday May 31st, 2008 02:41 am

In order to receive email on selected forums, click "My Account", then "Watched Forums" on the top. Select either "Email Posts as they come in" ...   Friday May 30th, 2008 12:27 pm

When Comfort is logged out, the UCM sends a message LU00. I have not verified if this happens at midnight, perhaps you can check it ...   Friday May 30th, 2008 11:55 am

Is the screenshot done after the vocab download? If so it shows that the vocabulary is in place, but it is an old vocabulary version ...   Sunday Apr 6th, 2008 02:40 pm

Article in CE Pro magazine --------------------------------------------------------------------------------  04.04.2008 — It’s apropos that the universal symbol used for a new idea is an icon of an incandescent light bulb. ...   Sunday Apr 6th, 2008 02:48 am

Specifications Frequency: EGSM Dual-band 900/1800 Mhz Connection to Comfort 12V, Com, KA,/KB (RS485), Voice/MIC Current from Comfort 50 milliamperes (idle), 250 mA (transmit) Max RF Output ...   Tuesday Apr 1st, 2008 12:55 pm

The UCM/GSM requires a GSM SIM card in order to operate.  For sales and pricing infomation, please contact sales@cytech.biz with all your information. ...   Tuesday Apr 1st, 2008 12:50 pm

I am afraid the ctouch does not have the facility to report historical status or event log, it only can show live status. However you ...   Monday Mar 17th, 2008 07:02 am

The X10 Remote control UR24 can be used with the Keypads, RIO (with IRD01 or IRR01) and SCS04/IR. When received these X10 IR codes are ...   Monday Mar 17th, 2008 03:03 am

Home automation products have long existed in small numbers, but a new study from ABI Research says that a technology shift now under way is ...   Saturday Mar 15th, 2008 04:57 am

When the doorbell (DP03) is pressed, the internal phones ring (RGR04 is needed) and the keypads chime. You can record a message to play on the ...   Saturday Mar 15th, 2008 02:29 am

If the Event Log reports the wrong zone names, it is probably because you do not have the correct Comfigurator cclx file for the system ...   Friday Mar 14th, 2008 03:14 pm

Cytech will be exhibiting at the National Homebuilding and Renovating Show at the NEC in Birmingham from the 10th to 13th April 2008 in conjunction ...   Saturday Mar 8th, 2008 08:03 am

Do you mean that you have forgotten the Engineer code? Try entering F0 and the code + # key on the keypad to confirm this. if ...   Wednesday Mar 5th, 2008 11:53 am

The PD6662.cct file should be included in Comfigurator 2.2.3. It is a template file ie .cct not a ccl file. You open it by File ...   Thursday Feb 28th, 2008 01:19 pm

The list is quite substantial as you can imagine, it would probably take me the rest of the week just to read it :D As usual, ...   Thursday Feb 28th, 2008 01:00 pm

I am not familiar with Homeseer so my answer applies to counters in general Refer to the rs232 protocol document in http://www.cytech.biz/Downloads/Files/163/rs232.pdf There are 256 counters in ...   Thursday Feb 28th, 2008 11:59 am

Old one was not actually ours, and is outdated anyway ...   Thursday Feb 28th, 2008 12:39 am

Comfort sending data to X10 is very reliable and consistent. However the performance of the XM10E  and CM12U could vary signiificantly abd even from unit ...   Wednesday Feb 27th, 2008 10:40 am

There may be a problem with the precision of the time of return in practice. You may not want the heating turned up a full day ...   Tuesday Feb 26th, 2008 11:29 pm

The PABX voicemail cannot be interfaced to other voicemail systems like Comfort. The protocol document shows how to use DTMF tones to access its own ...   Tuesday Feb 26th, 2008 10:12 pm

Thanks for that! I am sure many will find it useful By the way, I noticed that you used the wrong logo in the front page. ...   Tuesday Feb 26th, 2008 10:07 pm

I have not heard this problem before. Does it happen during a selective download ie shorter duration as well? Try downloading a default template (ie blank) ...   Tuesday Feb 26th, 2008 09:38 pm

Your ccl file does not have any dialout set for arm or disarm so there should not be any dial out when you disarm/unset normally However ...   Tuesday Feb 26th, 2008 12:31 pm

The manual shows how you can program the PABX to set it up according to what you need. It seems to be for ITS telecom ...   Tuesday Feb 26th, 2008 05:13 am

I can add it to my wish list.:) ...   Tuesday Feb 26th, 2008 04:28 am