The message below was posted by  Freeco in another forum, and has been moved to this more appropriate Troubleshooting Forum my system didn't work untill i ...   Thursday Aug 14th, 2008 01:52 pm

We are still testing and trying to appreciate all the possibilities of the software ...   Tuesday Aug 12th, 2008 12:55 pm

Feature Request duly noted regards ...   Tuesday Aug 12th, 2008 04:21 am

You can use a Pulse Output action between IR commands eg IR 1 to Output 1 Pulse Output 16 for 10 IR 2 to Output 3 etc The Pulse Output ...   Monday Aug 11th, 2008 12:06 pm

Tim The issue may be whether the Homesafe sign in alarm was triggered, as I dont have your ccl file, and cannot find the application guide ...   Monday Aug 11th, 2008 02:52 am

I suggest that you start a default file for Comfort I , set the number of door stations and keypads, and the zones programming and ...   Sunday Aug 10th, 2008 01:54 pm

when the keypad goes dead next time can you check if you can access the menu from a local telephone or remote telephone? If you ...   Sunday Aug 10th, 2008 02:44 am

The better way to do this is to use the Security Off alarm, enable the dialout to one or more phones, and in the Alarm ...   Saturday Aug 9th, 2008 02:55 am

Vicente I will contact you by email to sort out your vocabulary problems ...   Wednesday Aug 6th, 2008 12:04 pm

If you can see the Spanish words now, then there should be no problem Are you able to create a new file and select Spanish? ...   Wednesday Aug 6th, 2008 02:40 am

Curiouser and curiouser! Check the attached file. I have zone 1 programmed with some spanish words and the wordlist is Spanish Comfort I I wonder if the ...   Tuesday Aug 5th, 2008 01:04 pm

A integrator had a problem on site with a new Comfort system. He tried to arm, and got the fast beeps indicating some active zone ...   Tuesday Aug 5th, 2008 12:51 pm

The Output connections are wrong The centre 12V must go to the centre of the Comfort OP terminal block (12V) NOT -12V The OP connection goes to ...   Tuesday Aug 5th, 2008 07:37 am

I suspect that Comfigurator is using a different folder than what you used to save the files Copy this default.cfg into the same folder, then ipen ...   Tuesday Aug 5th, 2008 04:34 am

You can simply restart the timer to retrigger it You can STOP a timer but there is no action to restart it. A stopped timer is ...   Monday Aug 4th, 2008 01:38 pm

Can you open vocust.cfg in the Comfigurator folder and  check that the contents are >Custom WordList 00=Promenade,promnfor.cfg,sentence.cfg 01=Spanish Comfort I,cs-wl-sp.cfg,sentence_spa.cfg 02=Portuguese_v7,cs-wl-pt_v7.cfg,sentence-pt_v7.cfg Check that the files cs-wl-sp.cfg and sentence_spa.cfg are found ...   Monday Aug 4th, 2008 12:32 pm

I think your equipment may be having some strange effect. Can you call and ask if their equipment will affect auto-dialllers on the telephone line? Also ...   Monday Aug 4th, 2008 12:19 pm

The files are correct What are the wordlists you see in the wordlist window compared to my jpg file that I showed? Have you selected Comfort I ...   Monday Aug 4th, 2008 09:55 am

Do you have a battery connected? If not the system does not allow you to arm, as under reguations, battery disconnected is considered as low ...   Monday Aug 4th, 2008 04:47 am

If you unzip the 3 files in my original post and copy them into the Comfigurator folder this should allow you to see Spanish Comfort ...   Monday Aug 4th, 2008 03:08 am

If the TWS Current sensor is not able to detect the current, wind several turns of the switch wire through the current sensor to increase ...   Monday Aug 4th, 2008 02:57 am

"Please hang up" announcement means that Comfort is unable to detect a dial tone on the line as it seizes the line Your LCR device perhaps ...   Monday Aug 4th, 2008 02:55 am

Vicente I don't understand why you did not have the Comfort I Spanish residential wordlist as it used to be included with Comfigurator older versions. Were ...   Sunday Aug 3rd, 2008 02:15 pm

Your equipment list should be sufficient for the configuration The TWS modules is normally mounted in a separate enclosure from the low voltage Comfort modules so ...   Sunday Aug 3rd, 2008 01:35 pm

I am not sure what that entails. Do a Dial Test F3,3 to hear the dialing progress to get an idea of why the dialing ...   Sunday Aug 3rd, 2008 01:30 pm

Unzip the attached zip file to the Comfigurator folder. When you have a new file for Comfort I, go to Modules and Settings > Wordlists. you ...   Sunday Aug 3rd, 2008 03:44 am

That shows the RGR04 is working Check the jumper settings on the Ringer module shown in the RGR04 Manual at http://www.cytech.biz/Downloads/Files/200/rgr04man.pdf Try the larger ring amplitude and ...   Friday Aug 1st, 2008 08:38 am

That right. The say words action is used to make the announcements "doorbell", DoorBell end" and "doorbell call" and can be changed if required, or ...   Friday Aug 1st, 2008 08:22 am

Can you check if you connect a normal phone to Comfort if it rings? If it does not it may be a problem with the ...   Friday Aug 1st, 2008 01:24 am

Try the attached file. This has not been tested and may need some refinement On the 2nd press of the button within 10 to 60 seconds ...   Thursday Jul 31st, 2008 02:16 pm

There is an action "Force Dialout for Door station" which forces the door station to dial out when it is part of the Doorbell Response. ...   Wednesday Jul 30th, 2008 12:43 pm

For Door Station Dialout; Go to Alarm Types, select Doorbell. This alarm is activated when the doorbell is pressed when the system is armed to Away ...   Tuesday Jul 29th, 2008 01:45 pm

The Invalid Keypad Broadcast Enable problem has been identified and wil be fixed in the next beta regards ...   Tuesday Jul 29th, 2008 01:06 pm

Bug discovered in Comfigurator 2.2.3 (probably older versions as well). The use of Timer 64 will cause an "Unknown Exception" Error If you have used Timer ...   Tuesday Jul 29th, 2008 12:42 pm

You can leave the I/O Monitor in Comfigurator running by itself so that all messages are shown including the Input activations Later you can select all ...   Monday Jul 28th, 2008 02:20 pm

The more critical run will be for the Door stations and Keypads because of the sensitivity of the audio If you are passing near Mains it ...   Monday Jul 28th, 2008 01:39 am

I assume you are referring to the CWM Designer? We will see if such a change can be done in future version ...   Saturday Jul 26th, 2008 08:36 am

Output Elements means that the status of the element is via the specified Output, and Zone Element means the status comes from a zone or  ...   Saturday Jul 26th, 2008 08:19 am

We dont have a way of transmitting voice over the internet for CWM However the Everhome software, see http://www.comfortforums.com/forum27/845.html has that ability to emulate a keypad ...   Saturday Jul 26th, 2008 07:58 am

Thanks for the feedback. These will be fixed in the next release Outputs are from 1 to 64 for Comfort and Slaves, and 129 onwards for ...   Saturday Jul 26th, 2008 05:05 am