| Posted: Monday Oct 21st, 2024 01:55 am |
|
1st Post |
david8811
Member
| Joined: | Wednesday Aug 15th, 2018 |
| Location: | |
| Posts: | 29 |
| Status: |
Offline
|
back to top
|
Hi Mr Chiu,
I have programmed my zones 25 to 30 to bypass zone using SwitchNO response. They have been working fine for the last 2 years or so. However, last 2 or 3 weeks I realized that bypass switches are no longer working. Now, the system announces these zones as "zone Trouble". As a result, I cannot arm the system. Appreciate your support.Last edited on Monday Oct 21st, 2024 09:17 am by david8811
|
| Posted: Monday Oct 21st, 2024 09:18 am |
|
2nd Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
david8811 wrote: Hi Mr Chiu,
I have programmed my zones 25 to 30 to bypass zone using SwitchNO response. There have been working fine for the last 2 years or so. However, last 2 or 3 weeks I realized that bypass switches are no longer working. Now, the system announces these zones as "zone Trouble". As a result, I cannot arm the system. Appreciate your support.
Zone Trouble means there is a problem with the zone wiring. eg brokenm wiring. Are these zone using EOL resistors? What is the EOL shunts position on these zones. If there are wrng eg set to Double EOL position but the EOL resistors are not connected then you will have zone trouble.
if the shunts are set to NO EOL,. then you can test by disconnecting the zone wires from the zones. and connecting a wire to short and Open the zone, Do you get Zone Trouble?
|
| Posted: Monday Oct 21st, 2024 09:43 am |
|
3rd Post |
david8811
Member
| Joined: | Wednesday Aug 15th, 2018 |
| Location: | |
| Posts: | 29 |
| Status: |
Offline
|
back to top
|
I used Comfort configurator to setup the response. Does that required physical EOL resistor to be installed? Last edited on Monday Oct 21st, 2024 09:43 am by david8811
|
| Posted: Monday Oct 21st, 2024 11:04 am |
|
4th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
Can you send the cclx file to support@cytech.biz after scanning for modules and saving
|
| Posted: Monday Oct 21st, 2024 01:34 pm |
|
5th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
You cannot paste images in the forum. That does not work in this forum You have to attach the image. It is be`st to send the cclx file to suppport@cytech.biz
|
| Posted: Tuesday Oct 22nd, 2024 02:21 am |
|
6th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
your message cannot be read, it results in garbae, I have deleted them to mak the rest of the posts readable
Last edited on Tuesday Oct 22nd, 2024 02:47 am by slychiu
|
| Posted: Friday Oct 25th, 2024 09:12 am |
|
7th Post |
Swiss-Toni
UCM Pi Users
back to top
|
clean the terminals where the eol pins are on the panel they oxidise and can cause this issue
|
| Posted: Saturday Oct 26th, 2024 06:08 am |
|
8th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
From your email, you have purchased a new SEM01C without zone shunts but you have connected the old LEM03 (which has zone shunts) to this SEM01C. This caused th LEM03 zones to have zone trouble. You ether need to get a new LEM02B or LEM03B without zone shunts so that it can be compatible with the SEM01C, or connect 2 EOL resistors to every zone in the old LEM03 if you want to keep the old LEM03
|
| Posted: Saturday Nov 16th, 2024 01:29 pm |
|
9th Post |
david8811
Member
| Joined: | Wednesday Aug 15th, 2018 |
| Location: | |
| Posts: | 29 |
| Status: |
Offline
|
back to top
|
Hi Chiu
Thank you for your response. May i know what is the value of the EOL resistor i need to use?
|
| Posted: Tuesday Dec 10th, 2024 01:56 am |
|
10th Post |
david8811
Member
| Joined: | Wednesday Aug 15th, 2018 |
| Location: | |
| Posts: | 29 |
| Status: |
Offline
|
back to top
|
Hi Chiu
Can I share the 2.2k resistor between Z25 and Z26 as shown in below diagram?Attachment: Zone Resistor.jpg (Downloaded 11 times) Last edited on Tuesday Dec 10th, 2024 01:59 am by david8811
|
| Posted: Tuesday Dec 10th, 2024 02:17 am |
|
11th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
No, each zone must have its own 2k2 series resistor
|
| Posted: Friday Dec 20th, 2024 09:43 am |
|
12th Post |
david8811
Member
| Joined: | Wednesday Aug 15th, 2018 |
| Location: | |
| Posts: | 29 |
| Status: |
Offline
|
back to top
|
Chiu,
I have installed each zones separately with 2 EOL resistors connected to the old LEM03. Set the shunts to be away from the terminal blocks. Pressed the reset button. But the problem of Zones Trouble is still not resolved.
Kindly advise what could be the problem?Last edited on Friday Dec 20th, 2024 11:40 am by david8811
|
| Posted: Friday Dec 20th, 2024 09:46 am |
|
13th Post |
slychiu
Administrator
| Joined: | Saturday Apr 29th, 2006 |
| Location: | Singapore |
| Posts: | 5742 |
| Status: |
Offline
|
back to top
|
send t the cclx file to support@cytech.biz after scanning for modules and saving the file
|
| Posted: Sunday Dec 22nd, 2024 02:13 am |
|
14th Post |
david8811
Member
| Joined: | Wednesday Aug 15th, 2018 |
| Location: | |
| Posts: | 29 |
| Status: |
Offline
|
back to top
|
The cclx file has been sent. Appreciate your support
|
|
