Comfort Automation/ Security System Forums > Third Party (interfacing to Comfort) > CBus > UCM/CBUS Problems > Tracking Responses sending Cbus Commands |
Moderated by: hendy |
Author | Post | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Howser Member
|
I am using Comfigurator with Comfort 2Z Ultra (v 7.160), Cbus2 Ucm (v7.106)
I am using the Control Menu to send most of the On/Off commands to Cbus (mainly for using Comfort iPhone and my outgoing GSM Ucm) I have included a log (above) from Cbus Toolkit which shows Comfort Ucm/Cbus (EN_CMFT/COMFORT) ramping Kitchen Light 1 to 25% over 0 seconds after a trigger event is raised. I tried looking at all the responses where Kitchen Light One is referred to and for the life of me, I cannot track where in Comfort this occurs. |
||||||||||
slychiu Administrator
|
Can you send the cclx file to support@cytech.biz? |
||||||||||
Howser Member
|
Done, cclx file sent support@cytech.biz. |
||||||||||
slychiu Administrator
|
I do not see any where the Counter 39 is changed by any response or otherwise Note that changing Counter 39 value will also send the counter value to Cbus Eg if counter 39 is changed to 256/4 = 64 then that causes the Cbus deive to ramp to 25% Turn on Monitor I/O before doing the trigger, then look for CT27 report in the monitor. This may give a clue to what caused itIt may be UCM/Pi changing the counter |
||||||||||
Howser Member
|
This is what the monitor shows < CT273F00 < CT284900 < CT279900 < CT28A500 < CT274000 < CT284A00 Last edited on Sunday Sep 8th, 2019 02:14 pm by Howser |
||||||||||
slychiu Administrator
|
< CT273F00 means the counter 39 is changed to 64That accounts for cbus lighting group address 39 going to 25% I cant see from your responses that coumnter 39 is changed to this value. There shoukl be something else causing this. Could it be the Cbus Go to Tools > Bus Monitor and press Start before the trigger. Then copy theBus monitor |
||||||||||
Howser Member
|
Find attached the bus Monitor. Attachment: BusMonitor.txt (Downloaded 4 times) |
||||||||||
slychiu Administrator
|
This is the relevant message in Bus Monitpr 21: 40: 57: 945 ----< 03 12 71 32 37 33 46 31 34 02 <--->q273F14 21: 40: 57: 965 ----< 03 00 64 32 37 33 46 30 30 31 32 32 31 02 <--->/d273F001221 The line is red means UCM ID #2 sent Counter 39 value 3F ie 64. Comfort broadcast the counter 39 value = 3F Counter 37 is mapped to Lighting Group address 39. Hence when UCM/Cbus receives the message from group 39 from Cbus, it sends the Counter value to Comfort |
||||||||||
Howser Member
|
I have
My question is why Comfort re broadcasting GA 39, and why only GA 39? I thought UCM ID#2 will only update the Counter 39 and 40 in Comfort, and not broadcast their values back to Cbus? |
||||||||||
slychiu Administrator
|
I thought UCM ID#2 will only update the Counter 39 and 40 in Comfort, and not broadcast their values back to Cbus? That is correct. UCM/Cbus will not send the values back to Cbus which was received from Cbus. Go to the UCM/Cbus2 Monitor Mode. This will show the transmit and receive messages > means transmit line, < means receive line You can confirm here if CM/Cbus is resending to Groups 39 and 40 |
||||||||||
Howser Member
|
I could not get Comfigurator to connect to the UCM, even though Comfort ServerManager detected the UCM. So I disconnected the UCM for a few seconds and connected it again. Now I cannot reproduce the problem. This is what I am getting from the Monitor >all55D0000A872476s >all55D0000A870991s >all55D0000A860992s >all55D0000A862477s <0508CA00020E32E7 <050938001A273F2A28499F >all5538000227405Al <0509CA00090E11 >all5538000228FE9Bl >all55380002284A4Fl >all55D0000A872476s >all5538000228FE9Bl >all55D0000A870991s The Cbus Logs no longer shows Comfort changing the GA. Last edited on Tuesday Sep 10th, 2019 11:32 am by Howser |
||||||||||
slychiu Administrator
|
Look at it again when it happens again. Com,fort should not be sending back to the same GA |
||||||||||
Howser Member
|
Am having a similar issue again, this time, every time the alarm status changes. So when the alarm status changes to Day Mode, the following are changed by comfort according to Toolkit;
Attachment: AlarmStatusChange.txt (Downloaded 1 time) Last edited on Sunday Mar 8th, 2020 09:49 pm by Howser |
||||||||||
slychiu Administrator
|
If Comfort sends any messages to cbus it is due to the program. Comfiort will not randomely send messages Check the Day Mode Response in Misc events and Alarm Type Armed Response also check Alarms to Cbus in Cbus module Last edited on Monday Mar 9th, 2020 12:08 pm by slychiu |
||||||||||
Howser Member
|
I have searched the Comfigurator project for Cbus2 CbusUCM 56 5 and Cbus2 CbusUCM 56 47, could not find any. I have checked the Day Mode Responses in Miscellaneous Events, they have no Response. Last edited on Monday Mar 9th, 2020 08:17 am by Howser |
||||||||||
slychiu Administrator
|
pls send your cclx file to support@cytech.biz |
||||||||||
Howser Member
|
Email sent. |