Posted: Saturday Sep 7th, 2019 07:50 pm |
|
1st Post |
Howser
Member
back to top
|
I am using Comfigurator with Comfort 2Z Ultra (v 7.160), Cbus2 Ucm (v7.106)
DateTime= 2019/09/07 20:56:35.245 App= 202 Trigger Control Group= 014 Kitchen Unit= 008 PC_CNIEI/INL_CNI Event= Action Selector triggered : 50, 'Motion-AutoLights OFF'
DateTime= 2019/09/07 20:56:35.629 App= 056 Lighting Group= 039 Kitchen Light 1 Unit= 009 PC_PACA/MOHAUPAC Event= Group ramped to 063 ( 25%) over 12 seconds
DateTime= 2019/09/07 20:56:35.632 App= 056 Lighting Group= 040 Kitchen Light 2 Unit= 009 PC_PACA/MOHAUPAC Event= Group ramped to 073 ( 29%) over 30 seconds
DateTime= 2019/09/07 20:56:38.386 App= 056 Lighting Group= 039 Kitchen Light 1 Unit= 127 EN_CMFT/COMFORT Event= Group ramped to 064 ( 25%) over 0 seconds
DateTime= 2019/09/07 20:56:38.598 App= 202 Trigger Control Group= 014 Kitchen Unit= 009 PC_PACA/MOHAUPAC Event= Trigger Indicator Kill |
I am using the Control Menu to send most of the On/Off commands to Cbus (mainly for using Comfort iPhone and my outgoing GSM Ucm)
I have included a log (above) from Cbus Toolkit which shows Comfort Ucm/Cbus (EN_CMFT/COMFORT) ramping Kitchen Light 1 to 25% over 0 seconds after a trigger event is raised.
I tried looking at all the responses where Kitchen Light One is referred to and for the life of me, I cannot track where in Comfort this occurs.
|
Posted: Sunday Sep 8th, 2019 02:27 am |
|
2nd Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5499 |
Status: |
Offline
|
back to top
|
Can you send the cclx file to support@cytech.biz?
|
Posted: Sunday Sep 8th, 2019 07:11 am |
|
3rd Post |
Posted: Sunday Sep 8th, 2019 09:05 am |
|
4th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5499 |
Status: |
Offline
|
back to top
|
I do not see any where the Counter 39 is changed by any response or otherwise
Note that changing Counter 39 value will also send the counter value to Cbus Eg if counter 39 is changed to 256/4 = 64 then that causes the Cbus deive to ramp to 25%
Turn on Monitor I/O before doing the trigger, then look for CT27 report in the monitor. This may give a clue to what caused itIt may be UCM/Pi changing the counter
|
Posted: Sunday Sep 8th, 2019 02:13 pm |
|
5th Post |
Howser
Member
back to top
|
This is what the monitor shows
< CT273F00
< CT284900
< CT279900
< CT28A500
< CT274000
< CT284A00
Last edited on Sunday Sep 8th, 2019 02:14 pm by Howser
|
Posted: Monday Sep 9th, 2019 02:49 am |
|
6th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5499 |
Status: |
Offline
|
back to top
|
< CT273F00 means the counter 39 is changed to 64That accounts for cbus lighting group address 39 going to 25%
I cant see from your responses that coumnter 39 is changed to this value. There shoukl be something else causing this. Could it be the Cbus
Go to Tools > Bus Monitor and press Start before the trigger. Then copy theBus monitor
|
Posted: Monday Sep 9th, 2019 07:46 pm |
|
7th Post |
Posted: Tuesday Sep 10th, 2019 02:12 am |
|
8th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5499 |
Status: |
Offline
|
back to top
|
This is the relevant message in Bus Monitpr
21: 40: 57: 945 ----< 03 12 71 32 37 33 46 31 34 02 <--->q273F14
21: 40: 57: 965 ----< 03 00 64 32 37 33 46 30 30 31 32 32 31 02 <--->/d273F001221
The line is red means UCM ID #2 sent Counter 39 value 3F ie 64.
Comfort broadcast the counter 39 value = 3F
Counter 37 is mapped to Lighting Group address 39. Hence when UCM/Cbus receives the message from group 39 from Cbus, it sends the Counter value to Comfort
|
Posted: Tuesday Sep 10th, 2019 06:01 am |
|
9th Post |
Howser
Member
back to top
|
I have - Cbus GA 39 (Kitchen Light 1) mapped to Counter 39 and
- Cbus GA 40 (Kitchen Light 2) mapped to Counter 40.
When the Kitchen Trigger Control is set, a cbus unit (PC_PACA) sets GA 39 to 25% over 12 seconds and GA 40 to 29% over 30 seconds.
My question is why Comfort re broadcasting GA 39, and why only GA 39?
I thought UCM ID#2 will only update the Counter 39 and 40 in Comfort, and not broadcast their values back to Cbus?
|
Posted: Tuesday Sep 10th, 2019 09:17 am |
|
10th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5499 |
Status: |
Offline
|
back to top
|
I thought UCM ID#2 will only update the Counter 39 and 40 in Comfort, and not broadcast their values back to Cbus?
That is correct. UCM/Cbus will not send the values back to Cbus which was received from Cbus.
Go to the UCM/Cbus2 Monitor Mode. This will show the transmit and receive messages
> means transmit line, < means receive line
You can confirm here if CM/Cbus is resending to Groups 39 and 40
|
Posted: Tuesday Sep 10th, 2019 10:46 am |
|
11th Post |
Howser
Member
back to top
|
I could not get Comfigurator to connect to the UCM, even though Comfort ServerManager detected the UCM.
So I disconnected the UCM for a few seconds and connected it again.
Now I cannot reproduce the problem.
This is what I am getting from the Monitor
>all55D0000A872476s
>all55D0000A870991s
>all55D0000A860992s
>all55D0000A862477s
<0508CA00020E32E7
<050938001A273F2A28499F
>all5538000227405Al
<0509CA00090E11
>all5538000228FE9Bl
>all55380002284A4Fl
>all55D0000A872476s
>all5538000228FE9Bl
>all55D0000A870991s
The Cbus Logs no longer shows Comfort changing the GA.
Last edited on Tuesday Sep 10th, 2019 11:32 am by Howser
|
Posted: Tuesday Sep 10th, 2019 12:14 pm |
|
12th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5499 |
Status: |
Offline
|
back to top
|
Look at it again when it happens again. Com,fort should not be sending back to the same GA
|
Posted: Sunday Mar 8th, 2020 09:48 pm |
|
13th Post |
Howser
Member
back to top
|
Am having a similar issue again, this time, every time the alarm status changes.
So when the alarm status changes to Day Mode, the following are changed by comfort according to Toolkit;- GA 005 ramped to 054 (21%)
- GA 47 switched on
Am attaching the Monitor from CbusUCM.Attachment: AlarmStatusChange.txt (Downloaded 1 time) Last edited on Sunday Mar 8th, 2020 09:49 pm by Howser
|
Posted: Monday Mar 9th, 2020 05:26 am |
|
14th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5499 |
Status: |
Offline
|
back to top
|
If Comfort sends any messages to cbus it is due to the program.
Comfiort will not randomely send messages
Check the Day Mode Response in Misc events and Alarm Type Armed Response
also check Alarms to Cbus in Cbus module
Last edited on Monday Mar 9th, 2020 12:08 pm by slychiu
|
Posted: Monday Mar 9th, 2020 08:14 am |
|
15th Post |
Howser
Member
back to top
|
I have searched the Comfigurator project for Cbus2 CbusUCM 56 5 and Cbus2 CbusUCM 56 47, could not find any.
I have checked the Day Mode Responses in Miscellaneous Events, they have no Response.Last edited on Monday Mar 9th, 2020 08:17 am by Howser
|
Posted: Monday Mar 9th, 2020 08:30 am |
|
16th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5499 |
Status: |
Offline
|
back to top
|
pls send your cclx file to support@cytech.biz
|
Posted: Monday Mar 9th, 2020 10:43 am |
|
17th Post |
|