Posted: Tuesday Apr 16th, 2019 12:51 pm |
|
1st Post |
waynebr
Member
Joined: | Friday May 1st, 2009 |
Location: | United Kingdom |
Posts: | 89 |
Status: |
Offline
|
back to top
|
Hi I am trying to connect the Z-Wave module to Samsung Smart Things but am unable to find the network. Is it possible to connect it directly or do I need a Z-wave remote control first?
|
Posted: Wednesday Apr 17th, 2019 01:27 am |
|
2nd Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5493 |
Status: |
Offline
|
back to top
|
You need a zwave primary controller to include ucm /zwave.I do not know if smart things is a primary
|
Posted: Wednesday Apr 17th, 2019 08:14 am |
|
3rd Post |
Posted: Wednesday Apr 17th, 2019 08:19 am |
|
4th Post |
waynebr
Member
Joined: | Friday May 1st, 2009 |
Location: | United Kingdom |
Posts: | 89 |
Status: |
Offline
|
back to top
|
Thanks I can connect smart things to z wave but the z wave ucm keeps saying not in a network. I am waiting on some z wave products so not sure if it will change when they arrive.
|
Posted: Wednesday Apr 17th, 2019 08:23 am |
|
5th Post |
Swiss-Toni
UCM Pi Users
back to top
|
Not fully up on Zwave but I dont think you can connect to both or more than one controller
!
|
Posted: Wednesday Apr 17th, 2019 02:45 pm |
|
6th Post |
waynebr
Member
Joined: | Friday May 1st, 2009 |
Location: | United Kingdom |
Posts: | 89 |
Status: |
Offline
|
back to top
|
My understanding is that any wave can have only 1 primary controller. At the moment it looks like the ucm reads the network but dosnt join it. Once my z wave devices arrive I can rule out it being an issue of not having any active z wave nodes just in case smart things turns off the network when no nodes are present. Otherwise I will wait till I can get my hands on a ucm pi. Last edited on Wednesday Apr 17th, 2019 02:47 pm by waynebr
|
Posted: Saturday Apr 20th, 2019 02:25 pm |
|
7th Post |
waynebr
Member
Joined: | Friday May 1st, 2009 |
Location: | United Kingdom |
Posts: | 89 |
Status: |
Offline
|
back to top
|
I managed to get this to work, I had to put smarthings into inclusion mode by choosing a fibaro device and then scanning for this. It then detected virtual devices.
Next question what is the best way of getting it to turn the lights on/ off or dimming? I can write a response for the counter and set the counter but is there a way of sending the counter information through to CBUS without writing a load of if statements in the counter response?
|
Posted: Sunday Apr 21st, 2019 01:10 am |
|
8th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5493 |
Status: |
Offline
|
back to top
|
You can link a cbus address to zwave by making the same counter or flagFor example if the cbus address is mapped to flag and a zwave address is mapped to the same flag then when the zwave address cinnabar state the flag will cause the cbus address to change accordinglyCounters can be make to both systems for dimmingSo there is no need to use responses at all
|
Posted: Sunday Apr 21st, 2019 07:45 am |
|
9th Post |
waynebr
Member
Joined: | Friday May 1st, 2009 |
Location: | United Kingdom |
Posts: | 89 |
Status: |
Offline
|
back to top
|
Thanks for the reply,
I think I tried that initially and have just retried it but linking to the counter only updates the counter value and has no affect on the light (It doesn't appear to send the information to C-Bus) Maybe I am missing something?
I have attached an example of what I have done.Attachment: Counters 1.jpg (Downloaded 19 times)
|
Posted: Monday Apr 22nd, 2019 05:21 am |
|
10th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5493 |
Status: |
Offline
|
back to top
|
You have not mapped the counter to Cbus, at least not that you have shown. The same counter must be mapped to cbus in order to likk the 2 addresses together
|
Posted: Monday Apr 22nd, 2019 08:56 am |
|
11th Post |
waynebr
Member
Joined: | Friday May 1st, 2009 |
Location: | United Kingdom |
Posts: | 89 |
Status: |
Offline
|
back to top
|
HI I have looked at the manual again as I have the original manual, It looks like I have the original CBUS and not the CBUS2 is mapping only available on the CBUS2?
|
Posted: Monday Apr 22nd, 2019 09:17 am |
|
12th Post |
slychiu
Administrator
Joined: | Saturday Apr 29th, 2006 |
Location: | Singapore |
Posts: | 5493 |
Status: |
Offline
|
back to top
|
Yes the old ucm cbus does not support this. You can get the new ucm/cbus2 if you want this
|
Posted: Monday Apr 22nd, 2019 09:19 am |
|
13th Post |
|