Comfort Home Automation/ Security System Forums Home
Home Search search Menu menu Not logged in - Login | Register

Comfigurator 3.12.3
 Moderated by: admin
 New Topic   Reply   Printer Friendly 
 Rate Topic 
AuthorPost
 Posted: Tuesday Feb 13th, 2018 04:38 pm
   PM  Quote  Reply 
1st Post
slychiu
Administrator


Joined: Saturday Apr 29th, 2006
Location: Singapore
Posts: 4231
Status: 
Offline

  back to top

Comfigurator 3.12.2

Known Issues
  1. UCM/EHG - ehome to Comfort cannot select Comfort registers - pulldown menu is blank
  2. Vocabulary Upgrade error - For some systems Vocab u[pgrade stops at 23%, 50% and comfort is reset. Do not attempt Vocab upgrade at this time
  3. In View Modes; Automation and EMS, the Control Menu  status checkbox is shown, but the actual status is not displayed
The changes in the new beta software are

UCM/Cbus2
  • For Learn mode and Monitor mode, the sent and receive messages to Cbus ae shown (instead of just received messages). The sent and received message are converted to ASCII for display
Time Programs
  • Time programs screen has  number for Time programs. Time program number ie 1 to 32 is displayed so that when programming, users can relate to the number
Scan Modules
  • If you open a cclx file which is different Comfort  eg Open Comfort 2 Optimum but connected to Comfort 2 Ultra, after Scan for modules, the wrong model was displayed. Now Comfigurator will show the actual scanned model regardless of the open cclx file
View Modes
  • Fixed bug - In View Modes; Automation and EMS, the zones status checkbox is missing
  • Known Bug - in  In View Modes; Automation and EMS, the Control Menu  status checkbox is shown, but the actual status is not displayed
GSM Priority
  • Name of the Unused Bit 6 in Configuration flags change to to "GSM Priority Dialout (Requires firmware 7.136) and above. This causes dial out by UCM/GSM4 as priority even when the phone line is connected. By default, system will dial by fixed phone line, and when phone line is down, will dial out by GSM
Note that Windows XP is not supported after Comfigurator 3.12.1

Last edited on Thursday Jun 7th, 2018 11:34 am by slychiu



 Posted: Thursday Mar 1st, 2018 05:58 pm
   PM  Quote  Reply 
2nd Post
slychiu
Administrator


Joined: Saturday Apr 29th, 2006
Location: Singapore
Posts: 4231
Status: 
Offline

  back to top

Comfigurator 3.12.3

Bugs Fixed
  • for UCM/EHG The drop down list to select Comfort registers is missing
  • Control Menu did not show status in Simplified, automation, Simplified Modes
  • HIO upgrade when atte,pting to upgrade message "Selected module is not in the configuration "
  • In IRIO, Tx codes in IR codes Sets cannot select operation code. When file is saved and loaded then it is ok
  • In some cases, Vocabulary Upgrade has error at 23% and 50% and was not able to continue from last address. It should be able to continue from last address now
New Features
  • UCM GSM4 > Properties Alphanumeric ID default is "Cytech"
  • Supports new CM9001-EMS Environmental Monitoring System Product and KP04A



 Posted: Saturday Mar 10th, 2018 08:37 am
   PM  Quote  Reply 
3rd Post
slychiu
Administrator


Joined: Saturday Apr 29th, 2006
Location: Singapore
Posts: 4231
Status: 
Offline

  back to top

Comfigurator 3.12.3 has been released.
Comfigurator should prompt to upgrade, otherwise upgrade from Help > Check for Upgrades



 Current time is 02:05 pm
Top




UltraBB 1.172 Copyright © 2007-2014 Data 1 Systems