back to top

1. Execute Response in Comfigurator (DA) with multiple actions - security alarm actions eg bypass, Do Alarm cause subsequent actions do not work. eg Bypass zone 1, bypass zone 2, output 1 on Only Bypass zone 1 will work. However the Response executed by Comfort events will work
2. Bypass action has other problem of clearing a memory bit
3. After Upgrading firmware to 7.113, some unused zones (Null zone  Type)  may have Partition 3 setting, and this causes the system to be unable to arm, and causes the keypads to give a strange beeping sound. UCM and Keypad is unable to log in until the arming aborts after 5 minutes.
   
4. Actions Add counter, Add counter give wrong answer from 7.039
   
5. Vocabulary Upgrade does not work, causes vocabulary to be erased. This has been fixed in version 7.113
6. CM9000- OPT firmware bug Clear all outputs action 8 does not work
7. Do Action 190 serial command DABE does not do the actions following action 190 correctly. The 1st action is continually repeated
8. Action 73, 16 Get  keypadId/ If Keypad ID does not work

• Fixed bug if incoming time message has no seconds, the minutes change is not updated.
• Fixed occasional problem where KP04 "wrong text press *1" cannot work, still get wrong text press *1"  but after comfort reset this does not happen. Fixed the problem no more wrong text press *1.  LCD text is actually good but wrong status shown in Keypad
• Fixed Bug for sentence table upgrade failure
  
• Fixed BUG when entry door causes intruder alarm due to no sign in, the Entry zone restore message is not sent to SMS or CMS if the zone response or Alarm response  loads zones and if any other zones are triggered between the entry door open and the intruder alarm.
• Fixed bug from 7.099 - KNX and CBUS mapped to Comfort time could not change time in Comfort.
  
• Fixed BUG from 7.077  when controlling zwave from the control menu, smart polling did not work correctly. This has no effect on zwave control
• Program entry warning time actually programmed entry time BUG from 7.077

• Support 4 partitions in Comfort Alarm See http://www.comfortforums.com/forum16/4491.html
  
• Myma39 and Kate39 vocabulary includes voice menu changes for Partitions Menu for Zones, Users and Keypads.
• Requires Comfigurator 3.11.6
  

• Set maximum zone nased on last programmed nonzero Zone Type for Z?, KNX and C-Bus to report zones at reset, instead of all 96 zones or according to no of slaves. This takes care of virtual zones which exist outside installed slaves.

• If Feedback Type = counter, flag or output, and if action key 0 and 1 have No words, then action key 0 and 1 automatically control the counter, flag or output, eg Flag and output off/on, counter = 00 or FF

• Automatically detect LEM03 and write to EEPROM LEM03 checkbox location

• Added action 158:  158, counter number,  0 = clear, 1 = set, 2 = toggle
• Added  Action 73 param 28 = partition for armed/ disarmed
• Added Action 80 set partition for arming/disarming

• No of Non-detector Alarms increased from 28 to 31 for future use by Comfort
  
• If arm to same mode, reply with security mode instead of no reply MDss
• Support control messages to HIO
• Support EL command for EOL shunts settings for Comfort and SEM v7.100 +

Last edited on Sunday Nov 5th, 2017 10:03 am by slychiu

  back to top

  back to top

1. For Partitions, Eng Menu 4,5 say Keypad area announcement gives the wrong partition number
   
2. Execute Response in Comfigurator (DA) with multiple actions - security alarm actions eg bypass, Do Alarm cause subsequent actions do not work. eg Bypass zone 1, bypass zone 2, output 1 on Only Bypass zone 1 will work. However the Response executed by Comfort events will work
3. Bypass action has other problem of clearing a memory bit
4. After Upgrading firmware to 7.113, some unused zones (Null zone  Type)  may have Partition 3 setting, and this causes the system to be unable to arm, and causes the keypads to give a strange beeping sound. UCM and Keypad is unable to log in until the arming aborts after 5 minutes.
5. Actions Add counter, Add counter give wrong answer from 7.039
6. Action 73, 16 Get  keypadId/ If Keypad ID does not work

Last edited on Wednesday Apr 11th, 2018 12:46 pm by slychiu

  back to top

1. Execute Response in Comfigurator (DA) with multiple actions - security alarm actions eg bypass, Do Alarm cause subsequent actions do not work. eg Bypass zone 1, bypass zone 2, output 1 on Only Bypass zone 1 will work. However the Response executed by Comfort events will work
2. Bypass action has other problem of clearing a memory bit
3. After Upgrading firmware to 7.113, some unused zones (Null zone  Type)  may have Partition 3 setting, and this causes the system to be unable to arm, and causes the keypads to give a strange beeping sound. UCM and Keypad is unable to log in until the arming aborts after 5 minutes.
   
4. Actions Add counter, Add counter give wrong answer from 7.039
5. Partition keypad disarm does not off siren when disarm partition if there is a trouble alarm, until the code is entered 2 times
6. CM9000- OPT firmware bug Clear all outputs action 8 does not work
7. Do Action 190 serial command DABE does not do the actions following action 190 correctly. The 1st action is continually repeated

Last edited on Saturday Nov 4th, 2017 10:58 am by slychiu

  back to top