Comfort  Automation/ Security System Forums Home
Home Search search Menu menu Not logged in - Login | Register

Comfort to Lutron
 Moderated by: admin
 New Topic   Reply   Printer Friendly 
 Rate Topic 
AuthorPost
 Posted: Sunday Aug 27th, 2006 07:46 am
   PM  Quote  Reply 
1st Post
slychiu
Administrator


Joined: Saturday Apr 29th, 2006
Location: Singapore
Posts: 5493
Status: 
Offline

  back to top

An Application note for UCM01 to Lutron Interface is now available on the website http://www.cytech.biz/manuals.html



 Posted: Saturday Oct 19th, 2013 11:05 am
   PM  Quote  Reply 
2nd Post
Krobar
Member
 

Joined: Saturday Oct 19th, 2013
Location:  
Posts: 27
Status: 
Offline

  back to top

Hi,

I cant find this application note. Please could you send me a link.



 Posted: Saturday Oct 19th, 2013 01:30 pm
   PM  Quote  Reply 
3rd Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

The application note is attached, but it is out of date. It applies to the old UCM01

Now you can talk to Lutron (Grafik Eye) using the Universal UCM

In Universal UCM Properties, select UCM Type = Lutron as shown in the screenshot



The Response wizard is able to select the UCM as Lutron




Select Lutron, then the Lutron commands can be selected



This is the way to send commands to Lutron

We should do a new application note

Attachment: Lutron Application Note.pdf (Downloaded 0 times)



 Posted: Saturday Oct 19th, 2013 03:40 pm
   PM  Quote  Reply 
4th Post
Krobar
Member
 

Joined: Saturday Oct 19th, 2013
Location:  
Posts: 27
Status: 
Offline

  back to top

Thank you, this makes a lot more sense now.

If I want to integrate with both Lutron lighting and Heatmiser heating do I need a universal UCM and a Heatmiser UCM or just the universal UCM? (I don't understand the need for different UCMs when both systems are Ethernet based).



 Posted: Sunday Oct 20th, 2013 02:20 am
   PM  Quote  Reply 
5th Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

You need a Universal UCM for the Lutron as well as Heatmiser UCM
Both Universal UCM and Heatmiser UCM come without any interface, you have to buy  Rs232 or Ethernet separately

Lutron Grafik Eye has RS232, not sure if it also has ethernet?
If it uses the same protocol over Rs232 and ethernet then either can be used

Heatmiser products can be RS485 or wifi (different models)
The UCM/Heatmiser for Rs485 is currently supported, The Ethernet interface for Heatmiser is still not ready yet

Even if both are ethernet interfaces, the communications protocol is different for the two products so you need different ucms to understand the different commands

You may even have two  3rd party products which can be supported by UCM/Universal with Ethernet interface, even in this case you would need 2 UCM/Universals




 Posted: Saturday Jul 5th, 2014 05:37 pm
   PM  Quote  Reply 
6th Post
Krobar
Member
 

Joined: Saturday Oct 19th, 2013
Location:  
Posts: 27
Status: 
Offline

  back to top

Hi,

 

Finally got round to trying this. I cant change the UCM Universal type, it is locked at "Universal". Firmware is 6.026.



 Posted: Saturday Jul 5th, 2014 06:10 pm
   PM  Quote  Reply 
7th Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

The  UCM Command Type can be selected from the dropdown list as shown below
Make sure you Comfigurator version is the latest ie 3.8.8 or above





However note that the Lutron Graphic Eye command set may not be the same as what you have because these commands were developed many years ago




 Posted: Sunday Jul 6th, 2014 12:14 am
   PM  Quote  Reply 
8th Post
Krobar
Member
 

Joined: Saturday Oct 19th, 2013
Location:  
Posts: 27
Status: 
Offline

  back to top

Thank you. I have managed to set that and found the wizard you mention. How do I setup the IP of the Lutron? It seems to be expecting RS232 and my UCM has an Ethernet module as does my Lutron QSE-CI-NWK-E.



 Posted: Sunday Jul 6th, 2014 06:05 am
   PM  Quote  Reply 
9th Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

You set up the IP address using DS Manager if you have ETH02 or Comfort Server Manager if you have ETH03

Run the software from Comfigurator Options > Settings
You should be able to see the IP adress of the ETHxx. Note that this is not the ETH that is being used to program Comfort. It should be the one that is attached to the Univeral UCM



 Posted: Monday Jul 7th, 2014 08:15 am
   PM  Quote  Reply 
10th Post
ident
Administrator


Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

The Lutron Commands can be used for UCM/Universal or UCM general
Both UCMs are able to support Lutron commands


However there is an error in the Lutron Actions when more than 1 Control Unit is specified

This should be fixed in the future Comfigurator release (after 3.8.9)

If you send the commands to only 1 control unit then there is no problem



 Current time is 03:52 pm
Top




UltraBB 1.172 Copyright © 2007-2014 Data 1 Systems