View single post by ident
 Posted: Friday Nov 22nd, 2013 12:19 pm
 PM  Quote  Reply  Full Topic 
ident



Joined: Wednesday Aug 9th, 2006
Location: Singapore
Posts: 3493
Status: 
Offline

  back to top

Comfigurator 3.7.7 can be downloaded from http://www.cytech.biz/comfigurator.html

This fixes the  bugs found in 3.7.6 and added some useful features

A number of users reported exceptions in 3.7.6 some of which could not be duplicated. We would like feedback from them whether the exceptions still occur


Known Issues
  1. Read User Codes does not work
  2. Thermostat function registers are displayed by name but not in alphabetic order
  3. Heatmiser display date format in Heatmiser module properties are missing the / separator eg 21/1113 instead of 21/11/13
  4. Execute Responses when the Response is longer than 24 bytes will ask to write to Comfort but after writing, Execute Response will still ask to write to Comfort
  5. Display of Serial Numbers for Comfort is incorrect, shows Invalid. Serial Numbers are correct  for UCMs
  6. When reading event log and Comfigurator is on the GSM4 or Zwave or Heatimiser configuration tab, the event log may get an error message "Event Log Format Invalid.. RA.." The workaround is to move  the cursor away from GSM4, Zwave or Heatmiser UCMs before reading event log
  7. Module Scan may be interrupted by some status reports and give error message "Module Scan Timed out - Please retry later". If this occurs, just redo the Module scan
Bugs Fixed
  1. Action "Add Immediate"  causee Sensor 0 and Counter 0 to show as Referenced in blue. This also occurred  in older versions
  2. Write to KT03 by UCM/ETH02 (not direct to KT03 USB) if a network error closes the connection, does not give the option "Continue from Last Address" so requiring Write to KT03 again. This also occurred  in older versions
  3. When doing module scan by Remote Ethernet connection there may be a wrong message " Comfort firmware 7.xxx does not support Module Scan. Please add modules manually". 
  4. In UCM/Zwave where Switch Multilevel Nodes are mapped to Responses, if the Response number changes in Comfort, the mapped Response number does not change.
  5. When firmware is upgraded to 7.040, some Serial Numbers may be wrongly generated and cause exception
  6. In KT03 Simulation Mode, Flag state was not shown correctly (but is OK on actual KT03)
  7. When a new template is opened, and Scan for Modules is done in a system with a programmed KT03, after the KT03 is scanned, clicking in some of the KT03 pages will cause an Exception.
  8. when upgrading firmware for UCM/KNX, message says "Upgrading firmware to UCM/EIB"
  9. UCM/Zwave compatibility problem for Response created by older Comfigurator 3.6. Empty channel becomes converted to Channel 1 because a blank channel cannot be selected
New Features
  1. Zwave Poll time 0 help text changed to "The  Time Interval (in 10 second units) to poll mapped Zwave nodes for status . 255 means no polling. 0 means Smart Polling from Zwave 7.031"
  2. The Yellow Boxes in Comfigurator right pane used for Response Errors will appear only if there is content. This used to obscure more useful information which required the boxes to be resized
  3. After completing a Scan for Modules, if there is at least 1 "Not Polled" result,  a message will pop uo "One or more modules are not polled. Write Modules to Comfort?". This is useful as people often forget to write modules and settings after adding a module and scanning for it
  4. In Responses, "Duplicate Responses" is now available on Right Click. This duplicates the selected Response, which is useful when many similar responses are needed, differring by soemthing eg counter number
  5. Portugal Defaults changed to the correct Portuguese wordlist
  6. Sunrise/Sunset Times added many Portuguese cities and corrected Time zone

Last edited on Monday Apr 7th, 2014 03:46 pm by ident

 Close Window